MerCruiser 496 MAG Bravo Скачать руководство пользователя страница 112

Страница: 112 / 146

Section 5 - Maintenance

Page 104

90-864839061 NOVEMBER 2006

MerCathode System—

Electrode assembly replaces the Anode block. System should be

tested to ensure adequate output. The test should be performed where boat is moored,

using Quicksilver Reference Electrode and Test Meter.

Description

Location

Figure

Gearcase anode plate

Mounted on the underside of the lower

gearcase.

20336

Ventilation plate anode

Mounted on the front of the gearcase.

20338

MerCathode System

The MerCathode electrode is mounted

to the underside of the gimbal housing.

The MerCathode controler is mounted

on the engine or on the boat transom.

The controler harness connects to the

electrode harness.

20340

Anode kit (if equipped)

Mounted to the boat transom.

20341

Trim cylinder anodes

Mounted on each of the trim cylinders.

20342

Bearing carrier anode (Bravo One)

Located in front of the propeller,

between the front side of the propeller

and the gear housing.

20343

Propshaft anode (Bravo Three)

Located behind the aft propeller.

20344

Checking the Quicksilver MerCathode System

The MerCathode system should be tested to ensure adequate output. Perform the test

where boat is moored, using the reference electrode and test meter. Contact your

authorized Mercury MerCruiser dealer for service and information .

Содержание 496 MAG Bravo



















































































































































Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды

MerCruiser 496 MAG Bravo, Руководство пользователя

Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды