MerCruiser 496 MAG Bravo Скачать руководство пользователя страница 135

Страница: 135 / 146

Section 6 - Storage

90-864839061 NOVEMBER 2006

Page 127

1. Insert a small wire repeatedly to make sure that vent holes, water drain holes, and

passages are unobstructed and open.

6146

Sterndrive Water Drain Holes

a -

Speedometer pitot tube

b -

Trim tab cavity vent hole

c -

Trim tab cavity drain passage

d -

Gear housing water drain hole (1

each ‑ port and starboard)

e -

Gear housing cavity vent hole

f -

Gear housing cavity drain hole

CAUTION

Avoid damage to the sterndrive unit. The universal joint bellows will conform to its stored

position. A unit stored in a raised position may fail when the unit is returned to service.

Always store the sterndrive unit in the full down position.

2. Lower the sterndrive unit to the full down/in position.
3. For additional assurance against freezing and rust, after draining, fill the cooling system

with propylene glycol mixed to the manufacturer's recommendation to protect engine

to the lowest temperature to which it will be exposed during freezing temperatures or

extended storage

IMPORTANT: Mercury MerCruiser requires that propylene glycol antifreeze, mixed to the

manufacturers instructions, be used in the seawater section of the cooling system for

freezing temperatures or extended storage. Make sure that the propylene glycol antifreeze

contains a rust inhibitor and is recommended for use in marine engines. Be certain to follow

the propylene glycol manufacturer's recommendations.

Battery Storage

Whenever the battery will be stored for an extended period of time, be sure the cells are

full of water and the battery is fully charged and in good operating condition. It should be

clean and free of leaks. Follow the battery manufacturer's instructions for storage.

Power Package Recommissioning

1. Ensure that all cooling system hoses are connected properly and hose clamps are tight.

Содержание 496 MAG Bravo



















































































































































Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды

MerCruiser 496 MAG Bravo, Руководство пользователя

Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды