MerCruiser 496 MAG Bravo Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 146

background image

Section 2 - Getting to Know Your Power Package

Page 40

90-864839061 NOVEMBER 2006

• Engine oil pressure too low
• Engine temperature too hot
• Seawater pressure too low
The audio warning system will sound with an intermittent beeping if the following occurs:
• Sterndrive oil level too low

!

CAUTION

Operation of the engine after the audio warning system alarm has sounded could result

in damage to the power package. When the alarm has sounded, do not operate engine

except to avoid a hazardous situation.

If the alarm sounds, stop the engine immediately. Investigate cause and correct it, if

possible. If the cause cannot be determined, contact your authorized Mercury MerCruiser

dealer.

Testing The Audio Warning System

1. Turn the ignition switch to the "ON" position without cranking the engine.
2. Listen for the audio alarm. The alarm will sound if the system is functioning correctly.

Engine Guardian Strategy

IMPORTANT: Boat speed could be reduced to idle and may not respond to the throttle.
Engine Guardian Strategy is designed to help reduce the potential for engine damage by

reducing engine power when a potential problem is sensed by the ECM. Engine Guardian

monitors:
• Oil pressure
• Coolant temperature
• Seawater pressure
• Engine overspeed
• Exhaust Manifold Temperature [8.1 liter (496 cid) engines only]
Also the Engine Guardian Strategy will reduce engine power to 90 percent of maximum if

any sensor on the power package fails.
For example, if the water inlet becomes partially blocked, Engine Guardian Strategy will

reduce the available power level of the engine to help prevent damage from decreased

water flow to the engine. If the debris passes through and full water flow is restored, engine

power levels are restored to normal.
To avoid a possible recurrence of the problem you should contact an authorized dealer.

The ECM stores the fault and with this information the technician will be able to more rapidly

diagnose problems.

Warning Horn Signals

Most faults will cause the warning horn circuit to activate. How the warning horn activates

depends on how serious the problem is. There are four warning horn states:
• Caution ‑ horn signal varies with product line and calibration. Minimal guardian.
• Warning ‑ horn signal varies with product line and calibration.
• Severe ‑ horn is beeping constantly.
• Critical ‑ horn is beeping constantly and guardian will be at forced idle.

«
...
46
47
48
49
50
...
»

Содержание 496 MAG Bravo



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 496 MAG Bravo

Бренд: Jula Страницы: 17

Бренд: Toyota Страницы: 525

Бренд: Kubota Страницы: 47

Бренд: Kubota Страницы: 181

Бренд: Forest-Master Страницы: 16

Throttling Governor Kerosene Stationary Engines

Бренд: Worthington Страницы: 33

Бренд: HIFEI Technology Страницы: 2

Бренд: Yanmar Страницы: 231

Бренд: Chicago Pneumatic Страницы: 88

Бренд: DETROIT Страницы: 64

Grove - Servo Max

Бренд: Seeed Страницы: 9

Бренд: DANA Страницы: 2

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды