MerCruiser 496 MAG Bravo Скачать руководство пользователя страница 52

Страница: 52 / 146

Section 3 - On The Water

Page 44

90-864839061 NOVEMBER 2006

Safe Boating Suggestions

In order to safely enjoy the waterways, familiarize yourself with local and all other

governmental boating regulations and restrictions, and consider the following suggestions.

Know and obey all nautical rules and laws of the waterways.

• Mercury MerCruiser strongly recommends that all powerboat operators complete a

boating safety course. Courses are offered in the U.S.A. by: The U.S. Coast Guard

Auxiliary, The Power Squadron, The Red Cross and your state or provincial boating

law enforcement agency. Inquiries may be made to the Boating Hotline at

1‑800‑368‑5647 or the Boat U.S. Foundation at 1‑800‑336‑BOAT.

Perform safety checks and required maintenance.

• Follow a regular schedule and ensure that all repairs are properly made.

Check safety equipment on board.

• Here are some suggestions of the types of safety equipment to carry when boating:

•

Approved fire extinguishers

•

Signal devices: flashlight, rockets or flares, flag and whistle or horn

•

Tools necessary for minor repairs

•

Anchor and extra anchor line

•

Manual bilge pump and extra drain plugs

•

Drinking water

•

Transistor radio

•

Paddle or oar

•

Spare propeller, thrust hubs, and an appropriate wrench

•

First aid kit and instructions

•

Water‑proof storage containers

•

Spare operating equipment, batteries, bulbs and fuses

•

Compass and map or chart of the area

•

Personal flotation device (1 per person on board)

Watch for signs of weather change and avoid foul weather and rough-sea boating.
Tell someone where you are going and when you expect to return.
Passenger boarding.

• Stop the engine whenever passengers are boarding, unloading or are near the back

(stern) of the boat. Shifting the drive unit into neutral is not sufficient.

Use personal flotation devices.

• Federal Law requires that there be a U. S. Coast Guard approved life jacket (personal

flotation device), correctly sized and readily accessible for every person on board, plus

a throwable cushion or ring. We strongly advise that everyone wear a life jacket at all

times while in the boat.

Prepare other boat operators.

• Instruct at least 1 person on board in the basics of starting and operating the engine

and boat handling in case the driver becomes disabled or falls overboard.

Do not overload your boat.

Содержание 496 MAG Bravo



















































































































































Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды

MerCruiser 496 MAG Bravo, Руководство пользователя

Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды