MerCruiser 496 MAG Bravo Скачать руководство пользователя страница 109

Страница: 109 / 146

Section 5 - Maintenance

90-864839061 NOVEMBER 2006

Page 101

Serpentine Drive Belt

WARNING

Avoid possible serious injury. Make sure that the engine is turned off and the ignition key

is removed before inspecting belts.

8118

Belt Routing Diagram

a -

Idler pulley

b -

Water circulating pump pulley

c -

Crankshaft pulley

d -

Alternator pulley

e -

Seawater pump pulley

f -

Power steering pump pulley

g -

Tensioner pulley

Checking

1. Inspect the drive belt for proper tension and for the following:

•

Excessive wear

•

Cracks

NOTE: Minor, transverse cracks (across the belt width) may be acceptable. Longitudinal

cracks (in the direction of belt length) that join transverse cracks are NOT acceptable.

•

Fraying

•

Glazed surfaces

•

Proper tension ‑ 13 mm (1/2 in.) deflection, with moderate thumb pressure, on the

belt at the location that has the longest distance between two pulleys.

mc75130-1

Replacing

IMPORTANT: If a belt is to be reused, it should be installed in the same direction of rotation

as before.
The belt tensioner is designed to operate within the limits of arm movement provided by

the cast stops when the belt length and geometry are correct.

Содержание 496 MAG Bravo



















































































































































Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды

MerCruiser 496 MAG Bravo, Руководство пользователя

Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды