MerCruiser 496 MAG Bravo Скачать руководство пользователя страница 84

Страница: 84 / 146

Section 5 - Maintenance

Page 76

90-864839061 NOVEMBER 2006

Filling

CAUTION

Alcohol or Methanol based antifreeze or plain water, are not recommended for use in the

coolant section of the Closed Cooling System at any time.

CAUTION

Overheating from insufficient cooling water will cause engine and drive system damage.

Ensure that there is sufficient water always available at water inlet holes during operation.

CAUTION

Air trapped in the closed cooling section of an engine cooling system can cause the

engine to overheat resulting in engine damage. To minimize the possibility of trapping

air when initially filling the closed cooling system, position the boat so that the front of the

engine is higher than the rear of the engine.

NOTE: Add coolant only when engine is at normal operating temperature.

1. Remove the fill cap from the coolant recovery bottle and inspect the gasket. Replace

the gasket if necessary.

IMPORTANT: This closed cooling system flows coolant at a high rate. Higher idle speeds

increase dispersion of trapped air into the system making it more difficult to purge trapped

air. Operate at idle during filling and air purging when specified.
2. Fill to the full mark with the specified coolant.

Tube Ref No.

Description

Where Used

Part No.

122

Extended Life Antifreeze/

Coolant

Closed Cooling System

92-877770K1

3. Install the fill cap onto the coolant recovery bottle.

Changing

Contact your authorized Mercury MerCruiser dealer.

Drive Unit Oil

CAUTION

ENVIRONMENTAL HAZARD! Discharge of oil or oil waste into the environment is

restricted by law. Do not spill oil or oil waste into the environment when using or servicing

your boat. Contain and dispose of oil or oil waste as directed by local authorities.

Checking

NOTE: Oil level will fluctuate during operation. Oil level should be checked with the engine

cold, before starting.

Содержание 496 MAG Bravo



















































































































































Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды

MerCruiser 496 MAG Bravo, Руководство пользователя

Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды