MerCruiser 496 MAG Bravo Скачать руководство пользователя страница 93

Страница: 93 / 146

Section 5 - Maintenance

90-864839061 NOVEMBER 2006

Page 85

INSTALLATION

1. Install a new water‑separating fuel filter element into the filter cup. Push the element

into the cup until completely seated.

2. Install new O‑ring on the filter cup.
3. Attach the filter cap to the filter cup by grasping the filter cap and rotating it in a counter

clockwise direction while holding the filter cup stationary, until the filter cap locks

securely into place.

4. Install the fuel filter assembly slowly into the Cool Fuel Module to prevent spilling fuel,

and align the screws retained in the filter cap with the screw holes in the Cool Fuel

Module. Tighten the filter assembly retaining screws until hand tight.

5. Ensure that the filter cap is firmly seated against the Cool Fuel Module and torque each

filter assembly retaining screw.

Description

lb. in.

lb. ft.

Filter assembly retaining screw

6. Open fuel supply valve, if equipped.
7. Reconnect the Cool Fuel Module harness to the engine wiring harness.
8. Properly ventilate the engine compartment.

CAUTION

Overheating from insufficient cooling water will cause engine and drive system damage.

Ensure that there is sufficient water always available at water inlet holes during operation.

9. Supply cooling water to the engine.
10. Start the engine. Check for gasoline leaks around the fuel filter assembly. If leaks exist,

stop the engine immediately. Recheck the filter installation, clean spilled fuel and

properly ventilate the engine compartment. If leaks continue, stop engine immediately

and contact your authorized Mercury MerCruiser dealer.

Lubrication

Steering System

WARNING

Do not grease the steering cable while it is extended. Hydraulic lock could occur and

cause loss of steering control.

NOTE: If steering cable does not have grease fitting, inner wire of cable cannot be greased.

Содержание 496 MAG Bravo



















































































































































Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды

MerCruiser 496 MAG Bravo, Руководство пользователя

Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды