MerCruiser 496 MAG Bravo Скачать руководство пользователя страница 123

Страница: 123 / 146

Section 5 - Maintenance

90-864839061 NOVEMBER 2006

Page 115

17. Disconnect the quick‑connect fitting and water hose from the flush socket on the engine

by pressing the release button on the flush socket.

18488

a -

Quick‑connect fitting (water hose

end)

b -

Flush socket release button

18. Remove the quick‑connect fitting from the water hose.

18487

a -

Quick‑connect fitting (water hose

end)

b -

Water hose

19. Retain the quick‑connect fitting with the water hose end for repeated use by storing it

separately in a storage compartment on the boat for easy access.

IMPORTANT: Do not store the quick‑connect fitting in the flush socket on the engine. Doing

so would allow the seawater pump to suck air during engine operation causing an

overheating problem. Damages due to engine overheating are not covered by Mercury

MerCruiser Warranty.

25900

Quick‑connect fitting stored in the boat

a -

Quick‑connect fitting (water hose end)

Содержание 496 MAG Bravo



















































































































































Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды

MerCruiser 496 MAG Bravo, Руководство пользователя

Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды