MerCruiser 496 MAG Bravo Скачать руководство пользователя страница 3

Страница: 3 / 146

The Operation, Maintenance and Warranty Manual contains specific instructions for using

and maintaining your product. We suggest that this manual remain with the product for

ready reference whenever you are on the water.
Thank you for purchasing one of our Mercury MerCruiser products. We sincerely hope your

boating will be pleasant!
Mercury MerCruiser

Warranty Message

The product you have purchased comes with a

limited warranty

from Mercury Marine;

the terms of the warranty are set forth in the Warranty Sections of this manual. The warranty

statement contains a description of what is covered, what is not covered, the duration of

coverage, how to best obtain warranty coverage,

important disclaimers and limitations

of damages

and other related information. Please review this important information.

Mercury Marine products are designed and manufactured to comply with our own high

quality standards, applicable industry standards and regulations, as well as certain

emissions regulations. At Mercury Marine every engine is operated and tested before it is

boxed for shipment to make sure that the product is ready for use. In addition, certain

Mercury Marine products are tested in a controlled and monitored environment, for up to

10 hours of engine run time, in order to verify and make a record of compliance with

applicable standards and regulations. All Mercury Marine product, sold as new, receives

the applicable limited warranty coverage, whether the engine participated in one of the test

programs described above or not.

Read This Manual Thoroughly

IMPORTANT: If you don’t understand any portion of this manual, contact your dealer for

a demonstration of actual starting and operating procedures.

Notice

Throughout this publication, and on your power package,

WARNINGS

and

CAUTIONS

accompanied by the International Hazard Symbol

, may be used to alert the installer/

user to special instructions concerning a particular service or operation that may be

hazardous if performed incorrectly or carelessly.

Observe them carefully.

These Safety Alerts alone cannot eliminate the hazards that they signal. Strict compliance

with these special instructions while performing the service, plus common sense operation,

are major accident prevention measures.

WARNING

WARNING—indicates a potentially hazardous situation that, if not avoided, could result

in death or serious injury.

CAUTION

CAUTION—indicates a potentially hazardous situation that, if not avoided, may result in

minor or moderate injury or property damage. It may also be used to alert against unsafe

practices.

IMPORTANT: Indicates information or instructions that are necessary for proper operation

and/or maintenance.

Содержание 496 MAG Bravo



















































































































































Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды

MerCruiser 496 MAG Bravo, Руководство пользователя

Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды