MerCruiser 496 MAG Bravo Скачать руководство пользователя страница 34

Страница: 34 / 146

Section 2 - Getting to Know Your Power Package

Page 26

90-864839061 NOVEMBER 2006

PANEL MOUNT FEATURES

mc77019-1

a -

Neutral lock button

b -

Throttle only button

c -

Lanyard stop switch

d -

Control handle tension adjustment

screw

e -

Control handle

f -

Trim/tilt button

Neutral Lock Button -

Prevents accidental shift and throttle engagement. Neutral lock

button must be pushed into move the control handle out of neutral.

Throttle Only Button -

Allows engine throttle advancement without shifting the engine.

This is done by disengaging the shift mechanism from the control handle. The throttle only

button can be depressed only when the remote control handle is in the neutral position,

and should only be used to assist in starting the engine.

Lanyard Stop Switch -

Turns the ignition off whenever the operator (when attached to the

lanyard) moves far enough away from the operator's position to activate the switch. Refer

Lanyard Stop Switch

for information on the use of this switch.

Control Handle -

Operation of the shift and throttle are controlled by the movement of the

control handle. Push the control handle forward from neutral with a quick firm motion to the

first detent for forward gear. Continue pushing forward to increase speed. Pull the control

handle back from neutral with a quick firm motion to the first detent for reverse gear and

continue pushing back to increase speed.

Control Handle Tension Adjustment Screw - (not visible)

This screw is used to adjust

the effort required to move the remote control handle. Refer to instructions provided with

remote control for complete adjustment instructions.

Trim/Tilt Button -

Refer to

Power Trim

Содержание 496 MAG Bravo



















































































































































Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды

MerCruiser 496 MAG Bravo, Руководство пользователя

Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды