MerCruiser 496 MAG Bravo Скачать руководство пользователя страница 83

Страница: 83 / 146

Section 5 - Maintenance

90-864839061 NOVEMBER 2006

Page 75

3. Fill to full line with specified fluid.
IMPORTANT: If fluid is not visible in pump, contact your authorized Mercury MerCruiser

dealer.

Filling

1. Remove the fill cap/dipstick and observe the level.
2. Add the specified fluid to bring the fluid level up to the proper range.

Tube Ref No.

Description

Where Used

Part No.

Dexron III Automatic

Transmission Fluid

Power steering system

Obtain Locally

114

Power Trim and Steering Fluid

Power steering system

92-858074K01

3. Reinstall the fill cap/dipstick.

Changing

Power steering fluid does not require changing unless it becomes contaminated with water

or debris. Contact your authorized Mercury MerCruiser dealer.

Engine Coolant

Checking

WARNING

Allow the engine to cool down before removing the coolant pressure cap. A sudden loss

of pressure could cause hot coolant to boil and discharge violently. After the engine has

cooled, turn the cap 1/4 turn to allow any pressure to escape slowly, then push down and

turn the cap all the way off.

1. With the engine at normal operating temperature, check the coolant level in the coolant

recovery bottle.

5649

a -

Coolant recovery bottle

2. Add the specified fluid as necessary.

Tube Ref No.

Description

Where Used

Part No.

122

Extended Life Antifreeze/

Coolant

Closed Cooling System

92-877770K1

Содержание 496 MAG Bravo



















































































































































Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды

MerCruiser 496 MAG Bravo, Руководство пользователя

Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды