MerCruiser 496 MAG Bravo Скачать руководство пользователя страница 120

Страница: 120 / 146

Section 5 - Maintenance

Page 112

90-864839061 NOVEMBER 2006

CAUTION

Avoid engine damage from overheating. If the engine is operated above 1500 RPM

during flushing, suction created by the seawater pickup pump may collapse the flushing

water hose causing the engine to overheat.

9. Slowly advance throttle until engine reaches 1300 RPM (+/‑100 RPM).

CAUTION

Engine overheating can cause engine damage. To avoid, observe the water temperature

gauge and ensure that the engine is operating in the normal range.

10. Observe the water temperature gauge to ensure that the engine is operating in the

normal range.

11. Operate engine with sterndrive in neutral for about 10 minutes or until discharge water

is clear.

12. Slowly return throttle to idle speed position.
13. Stop engine.
14. Shut off the water and remove flushing attachments.
15.

If the boat is out of the water:

Install the water inlet hose to the aft side of the seawater

pump. Tighten the hose clamp securely.

16.

If the boat is in the water:

Tag the ignition switch with an appropriate tag requiring

the seawater inlet hose to be reconnected prior to operating engine.

The SeaCore Power Package Flushing Procedure

NOTE: Flushing is needed only for salt, brackish, mineral laden or polluted water

applications. Flushing is recommended after each outing for best results.

IMPORTANT: Flushing the SeaCore power package with the boat and sterndrive in the

water is less effective. Flushing the SeaCore power package is most effective when

performed with the boat and sterndrive out of the water, such as on a boat lift or trailer.

MODELS USING THE STERNDRIVE WATER PICKUP

IMPORTANT: The system is designed to flush the Bravo sterndrive and the engine with

one water source. Do not block or remove the inlet water hose from the sterndrive to the

engine.

NOTE: Engines with the sterndrive water inlet blocked off at the gimbal housing: Refer to

Alternative Water Pickups.

WARNING

Contact with moving drive components and the propeller can cause personal injury or

death. To avoid possible injury, remove the propeller and ensure that no people or

animals are in the area of the drive unit while flushing.

IMPORTANT: Do not allow the engine to pull air or seawater from alternative water pickup

sources during the flushing procedure. If equipped, ensure that all alternative water inlet

hoses are plugged at both ends.
1. Remove the boat from the water.

Содержание 496 MAG Bravo



















































































































































Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды

MerCruiser 496 MAG Bravo, Руководство пользователя

Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды