MerCruiser 496 MAG Bravo Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 146

background image

Section 6 - Storage

90-864839061 NOVEMBER 2006

Page 119

ENGINE AND FUEL SYSTEM PREPARATION

!

WARNING

Avoid serious injury or death from a gasoline fire or explosion; gasoline is extremely

flammable and highly explosive under certain conditions. When servicing the fuel system

components ensure that the engine is cool, the ignition switch is in the off position, and

that the lanyard stop switch, if equipped, is in the off position. Do not smoke or allow

spark or open flame in the area. Wipe up any spilled fuel immediately. Ensure that no

fuel leaks exist before closing the engine hatch.

!

WARNING

Fuel vapors can be present in the engine compartment. Avoid injury or power package

damage caused by fuel vapors or explosion. Always ventilate the engine compartment

prior to servicing the power package.

1. In a 23 liter (6 U.S.gal.) remote fuel tank mix:

a.

19 liter (5 U.S. gal) regular unleaded 87 octain (90 RON) gasoline

b.

1.89 liter (2 U.S. qts.) Premium Plus 2‑Cycle TC‑W3 Outboard Oil

c.

150 ml (5 ounces) Fuel System Treatment and Stabilizer or 30 ml (1 ounce) Fuel

System Treatment and Stabilizer Concentrate

Tube Ref No.

Description

Where Used

Part No.

115

Premium Plus 2-cycle TC-W3

Outboard Oil

Fuel system

92-802824A1

124

Fuel System Treatment &

Stabilizer

Fuel system

802875A1

2. Allow the engine to cool down.
IMPORTANT: Immediately wipe up any fuel spills or sprays.
3. Close the fuel shut off valve, if equipped. Disconnect and plug the fuel inlet fitting if not

equipped with a fuel shut off valve.

4. Connect the remote fuel tank (with the fogging mixture) to the fuel inlet fitting.
IMPORTANT: Supply cooling water to the engine.
5. Start and operate the engine at 1300 rpm for 5 minutes.
6. After specified operating time is complete, slowly return throttle to idle rpm and shut

engine off.

IMPORTANT: Ensure that some fogging mixture remains in the engine. Do not allow the

engines fuel system to become completely dry.
7. Replace the water separating fuel filter element. Refer to Section 5 for proper

procedure.

Draining the Seawater System

!

CAUTION

Excess water in the bilge can damage the engine or cause the boat to sink. Ensure that

the boat is out of the water, the seacock is closed (if equipped) or the seawater inlet hose

is disconnected and plugged on both ends, and the bilge pump is operating before

beginning the draining procedure.

«
...
125
126
127
128
129
...
»

Содержание 496 MAG Bravo



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 496 MAG Bravo

Бренд: Rail King Страницы: 46

Бренд: TAARKS Страницы: 7

PRESTIGE PS2.60FA

Бренд: CAB Страницы: 16

Бренд: Grizzly Страницы: 2

Crankcase for Harley-Davidson

Бренд: S&S Cycle Страницы: 12

Бренд: Volkswagen Страницы: 17

90000 I/C 525 Series

Бренд: Briggs & Stratton Страницы: 16

Бренд: Parker Страницы: 32

Бренд: Kober Страницы: 112

Бренд: Dietz Страницы: 10

Бренд: Dietz Страницы: 11

Бренд: STG-BEIKIRCH Страницы: 25

Бренд: Motion Страницы: 92

Бренд: Motion Страницы: 124

Бренд: B&R Страницы: 98

Бренд: Motus Страницы: 32

Бренд: Mitsubishi Heavy Industries Страницы: 220

Бренд: JAC Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды