MerCruiser 496 MAG Bravo Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 146

background image

Section 5 - Maintenance

90-864839061 NOVEMBER 2006

Page 83

2. Remove the IAC muffler.

a

18495

IAC muffler installed in the throttle body

a -

IAC muffler

3. Inspect the IAC muffler for damage such as, holes, cracks or deterioration. Replace

the IAC muffler if damaged.

IMPORTANT: Do not use cleaner containing methyl ethyl ketone.
IMPORTANT: Do not get cleaner on electrical connections.
4. Clean or replace the IAC muffler if grey or black, as the muffler should be white.
5. Clean the IAC muffler with warm water and a mild detergent.
6. Allow the IAC muffler to completely air dry before use.
7. Reinstall the IAC muffler.

Water‑Separating Fuel Filter (496)

Water‑Separating Fuel Filter

!

WARNING

Avoid serious injury or death from a gasoline fire or explosion; gasoline is extremely

flammable and highly explosive under certain conditions. When servicing the fuel system

components ensure that the engine is cool, the ignition switch is in the off position, and

that the lanyard stop switch, if equipped, is in the off position. Do not smoke or allow

spark or open flame in the area. Wipe up any spilled fuel immediately. Ensure that no

fuel leaks exist before closing the engine hatch.

!

WARNING

Avoid serious injury or death caused by fire or explosion. The fuel system is pressurized

during operation. Use care when removing the fuel filter. Fuel could spray on the hot

engine causing fire or explosion. Allow the engine to cool down and relieve fuel system

pressure before attempting to remove the fuel filter.

«
...
89
90
91
92
93
...
»

Содержание 496 MAG Bravo



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 496 MAG Bravo

Бренд: ABB Страницы: 8

Бренд: Quectel Страницы: 71

Бренд: Painless Performance Страницы: 24

Бренд: Shindaiwa Страницы: 48

Бренд: Kohler Страницы: 4

Бренд: MSW Страницы: 159

Бренд: Selve Страницы: 132

Бренд: A'OK Страницы: 7

Бренд: Eastwood Страницы: 20

Бренд: DLE Страницы: 4

Бренд: DLE Страницы: 24

Бренд: Mitsubishi Страницы: 76

Бренд: LONCIN Страницы: 64

Бренд: Farymann Diesel Страницы: 137

Бренд: D-MOTOR Страницы: 50

Бренд: DLE Страницы: 13

USB Protocol Suite

Бренд: LeCroy Страницы: 107

Бренд: Toyota Страницы: 222

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды