background image

Section 6 - Storage 

Page  118

90-864839061   NOVEMBER  2006

Cold Weather or Extended Storage

IMPORTANT:  Mercury  MerCruiser  strongly  recommends  that  this  service  should  be

performed  by  an  authorized  Mercury  MerCruiser  dealer.  Damage  caused  by  freezing

temperatures IS NOT covered by the Mercury MerCruiser Limited Warranty.

!

 CAUTION

Seawater that is trapped in or remains in the cooling system seawater section during cold

weather  or  winter  storage  can  freeze  resulting  in  cooling  system  or  engine  damage.

Completely  drain  the  seawater  from  the  cooling  system  seawater  section  for  winter

storage  or  immediately  after  cold  weather  operation  when  the  possibility  of  freezing

temperatures exist.

IMPORTANT: Mercury MerCruiser requires that propylene glycol antifreeze, mixed to the

manufacturers  instructions,  be  used  in  the  seawater  section  of  the  cooling  system  for

freezing temperatures or extended storage. Make sure that the propylene glycol antifreeze

contains a rust inhibitor and is recommended for use in marine engines. Be certain to follow

the propylene glycol manufacturer's recommendations.

Preparing Power Package for Storage

1. Fill the fuel tanks with fresh gasoline (that does not contain alcohol) and a sufficient

amount of Quicksilver Gasoline Stabilizer for Marine Engines to treat the gasoline.

Follow instructions on the container.

2. If the boat is to be placed in storage with fuel containing alcohol in fuel tanks (if fuel

without alcohol is not available): Fuel tanks should be drained as low as possible and

Mercury/Quicksilver  Gasoline  Stabilizer  for  Marine  Engines  added  to  any  fuel

remaining in the tank. Refer to 

Fuel Requirements

 for additional information.

3. Flush the cooling system. Refer to the 

Maintenance

 section.

4. Supply cooling water to engine. Refer to the 

Maintenace

 section

5. Operate the engine sufficiently to bring it up to normal operating temperature and allow

fuel with Mercury/Quicksilver Gasoline Stabilizer to circulate through the fuel system.

Shut off the engine.

6. Change the oil and oil filter.
7. Prepare the engine and fuel system for storage. Refer to 

Engine and Fuel System

Preparation

.

8. Drain the engine seawater cooling system. Refer to 

Draining the Seawater System

.

!

 CAUTION

If the boat is in the water, the seacock must remain closed until the engine is to be

restarted to prevent water from flowing back into the cooling system or the boat. If the

boat is not fitted with a seacock, leave the water inlet hose disconnected and plugged to

prevent water from flowing back into the cooling system or the boat. As a precautionary

measure, attach a tag to the ignition switch or steering wheel of the boat with the warning:

Open the seacock or reconnect the water inlet hose before starting the engine.

9. For  additional  assurance  against  freezing  and  rust,  after  draining,  fill  the  seawater

cooling system with propylene glycol mixed to the manufacturer's recommendation to

protect engine to the lowest temperature to which it will be exposed during freezing

temperatures or extended storage.

10. Store the battery according to the manufacturer's instructions.

Содержание 496 MAG Bravo



















































































































































Отзывы: