MerCruiser 496 MAG Bravo Скачать руководство пользователя страница 87

Страница: 87 / 146

Section 5 - Maintenance

90-864839061 NOVEMBER 2006

Page 79

All Other Models:

Place the sterndrive unit in full trim limit out position, remove the oil

fill/drain screw and sealing washer and drain the oil.

mc79507-1

a -

Oil fill/drain screw

b -

Sealing washer

6. Remove the oil vent screw and sealing washer. Allow the oil to drain completely.

mc77106-1

a -

Oil vent screw

b -

Sealing washer

IMPORTANT: If any water drained from the oil fill/drain hole, or if the oil appears milky, the

sterndrive unit is leaking and should be checked immediately by your authorized Mercury

MerCruiser dealer.
7. Lower the sterndrive unit so that the propeller shaft is level. Fill the sterndrive unit,

through the oil fill/drain hole, with specified gear lubricant until an air‑free stream of

lubricant flows from oil vent hole.

Tube Ref No.

Description

Where Used

Part No.

High Performance Gear

Lubricant

Sterndrive unit

92-802854A1

IMPORTANT: Use only Mercury/Quicksilver High Performance Gear Lubricant in

sterndrive unit.
8. Install the oil vent screw and sealing washer.
9. Continue to pump gear lubricant into the drive through the oil fill/drain hole until the

gear lubricant appears in the gear lube monitor.

10. Fill the monitor so that the oil level is in the operating range. Do not overfill. Ensure that

the rubber gasket is inside the cap and install. Do not overtighten.

NOTE: Oil capacity includes gear lube monitor.

Содержание 496 MAG Bravo



















































































































































Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды

MerCruiser 496 MAG Bravo, Руководство пользователя

Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды