MerCruiser 496 MAG Bravo Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 146

background image

Section 3 - On The Water

Page 56

90-864839061 NOVEMBER 2006

!

CAUTION

Serious engine damage could occur by failing to follow these instructions. Sand, silt or

mud could be sucked into the water inlets restricting or shutting off the water supply to

the engine.

Extreme care should be exercised when operating a boat equipped with low water inlets

while maneuvering in shallow water. Also, avoid beaching a boat with the engine operating.

Conditions Affecting Operation

Weight Distribution (Passengers and Gear) Inside the Boat

Shifting weight to rear (stern):
• Generally increases speed and engine RPM
• Causes bow to bounce in choppy water
• Increases danger of following wave splashing into the boat when coming off plane
• At extremes, can cause the boat to porpoise
Shifting weight to front (bow):
• Improves ease of planing
• Improves rough water ride
• At extremes, can cause the boat to veer back and forth (bow steer)

Bottom Of Boat

To maintain maximum speed, the boat bottom should be:
• Clean, free of barnacles and marine growth
• Free of distortion; nearly flat where it contacts the water
• Straight and smooth, fore and aft
Marine vegetation may accumulate when the boat is docked. This growth must be removed

before operation; it may clog the water inlets and cause the engine to overheat.

Cavitation

Cavitation occurs when water flow cannot follow the contour of a fast‑moving underwater

object, such as a gear housing or a propeller. Cavitation permits the propeller to speed up,

but the boat speed to reduce. Cavitation can seriously erode the surface of the gear housing

or the propeller. Common causes of cavitation are:
• Weeds or other debris snagged on the propeller
• Bent propeller blade
• Raised burrs or sharp edges on the propeller

Ventilation

Ventilation is caused by surface air or exhaust gases that are introduced around the

propeller resulting in propeller speed‑up and a reduction in boat speed. Air bubbles strike

the propeller blade and cause erosion of the blade surface. If allowed to continue, eventual

blade failure (breakage) will occur. Excessive ventilation is usually caused by:
• Drive unit trimmed out too far.
• A missing propeller diffuser ring.
• A damaged propeller or gear housing, which allows exhaust gases to escape between

propeller and gear housing.

• Drive unit installed too high on transom.

«
...
62
63
64
65
66
...
»

Содержание 496 MAG Bravo



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 496 MAG Bravo

VLT AutomationDrive FC 300 Series

Бренд: Danfoss Страницы: 56

Бренд: Danfoss Страницы: 2

Бренд: Saito Страницы: 2

Бренд: RCV Страницы: 4

3T-MOTORS 3T45-10E

Бренд: 3T-Components Страницы: 12

3T-MOTORS 3T35-13

Бренд: 3T-Components Страницы: 24

3T-MOTORS 3T35-10SD

Бренд: 3T-Components Страницы: 16

3T-MOTORS 3T35-10R

Бренд: 3T-Components Страницы: 20

Бренд: Cobra Страницы: 15

Бренд: IMS Страницы: 6

Бренд: STEPCRAFT Страницы: 24

Бренд: Atlas Imperial Diesel Engine Страницы: 59

LZB 77 A0017-15

Бренд: Atlas Copco Страницы: 120

Бренд: Volvo Страницы: 72

Бренд: CAME Страницы: 80

Бренд: Honda Страницы: 33

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды