MerCruiser 496 MAG Bravo Скачать руководство пользователя страница 85

Страница: 85 / 146

Section 5 - Maintenance

90-864839061 NOVEMBER 2006

Page 77

1. Check the gear lube oil level. Keep the oil level within the recommended operating

range. If any water is visible at the bottom of the monitor or appears at the oil fill/drain

plug and/or if oil appears discolored, contact your authorized Mercury MerCruiser

dealer immediately. Both conditions may indicate a water leak somewhere in the

sterndrive unit.

8530

a -

Gear lube monitor

Filling

IMPORTANT: If more than 59 ml (2 fl. oz.) of High Performance Gear Lubricant is required

to fill the monitor, a seal may be leaking. Damage to the sterndrive unit may occur due to

lack of lubrication. Contact your authorized Mercury MerCruiser dealer.
1. Remove the gear lube monitor cap.
2. Fill the monitor with the specified fluid so that the oil level is in the operating range. Do

not overfill.

Tube Ref No.

Description

Where Used

Part No.

High Performance Gear

Lubricant

Gear lube monitor

92-802854A1

3. Replace the cap.

NOTE: When filling the entire sterndrive unit refer to Changing instructions, following.

Содержание 496 MAG Bravo



















































































































































Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды

MerCruiser 496 MAG Bravo, Руководство пользователя

Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды