Lenovo ThinkAgile VX 4-Socket 4U Certified Node Скачать руководство пользователя страница 293

Страница: 293 / 296

front bezel

130

front cover

131

front operator panel

134

front USB/VGA assembly

137

hard disk drive backplane (lower tray)

141

hard disk drive backplane (upper tray)

139

heat sink

190

hot-swap drive

147

hot-swap drive filler

150

I/O adapter (slot 16 to 17)

I/O tray

152

left riser

212

LOM adapter (slot 9)

M.2 backplane

163

M.2 drive

166

memory air baffle

170

memory module

removing

173

memory module filler

removing

173

microprocessor

190

microprocessor heat sink module

190

midplane

179

operator panel

134

PCIe adapter (slot 1 to 4)

PCIe adapter (slot 10 to 15)

PCIe adapter (slot 5 to 8)

PHM

power supply

power supply filler

processor

processor-heat-sink module

190

RAID flash power module (lower)

208

RAID flash power module (upper)

207

RAID/HBA card (lower)

201

RAID/HBA card (upper)

200

removing

filler (memory module)

memory module

memory module filler

right riser

riser bracket (slot 14 to 15)

215

riser for slot 1 to 4

212

riser for slot 10 to 15

213

riser for slot 16 to 17

217

storage board assembly

224

storage interposer (lower)

228

storage interposer (upper)

storage tray

system battery

system board

system board filler

TCM/TPM adapter

top cover

tray filler (upper)

upper tray filler

replacement

CR2032 battery

105

system battery

105

replacing

adapter

compute tray

CPU

DIMM

DIMM air baffle

fan

fan cage

filler (System board)

front bezel

front cover

front operator panel

front USB/VGA assembly

137

hard disk drive backplane

139

heat sink

190

hot-swap drive

147

hot-swap drive filler

I/O tray

M.2 backplane

M.2 drive

memory air baffle

memory module

microprocessor

microprocessor heat sink module

midplane

PHM

power supply

power supply filler

processor

processor heat sink module

190

RAID flash power module

207

RAID/HBA card

200

riser

212

storage board assembly

storage interposer

storage tray

System board

System board filler

TCM/TPM adapter

upper tray filler

right riser

installing

220

riser

replacing

212

riser 1

removing

212

riser 2

removing

213

riser bracket (slot 14 to 15)

installing

221

removing

215

riser connectors

riser for slot 1 to 4

installing

218

removing

212

riser for slot 10 to 15

installing

220

removing

213

riser for slot 16 to 17

installing

222

removing

217

safety

safety inspection checklist

Secure Boot

162

serial-device problems

260

server

identification

rear view

server components

server package contents

server power on or power off problems

251

server setup checklist

service advisories

service and support

before you call

hardware

software

service data

service label

software problems

265

software service and support telephone numbers

273

solid state drive activity LED

solid state drive status LED

solving

Ethernet controller problems

250

insufficient PCIe resource

259

283

Содержание ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Результаты поиска

Содержание ThinkAgile VX 4-Socket 4U Certified Node

Отзывы:

Похожие инструкции для ThinkAgile VX 4-Socket 4U Certified Node

Бренды по названию

Популярные бренды

Lenovo ThinkAgile VX 4-Socket 4U Certified Node, Руководство пользователя

Результаты поиска

Содержание ThinkAgile VX 4-Socket 4U Certified Node

Отзывы:

Похожие инструкции для ThinkAgile VX 4-Socket 4U Certified Node

Бренды по названию

Популярные бренды