Lenovo ThinkAgile VX 4-Socket 4U Certified Node Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 296

background image

Remove a LOM adapter from slot 9

The LOM adapter in slot 9 is in the I/O tray that is accessed from the rear of the server. After removing the I/O

tray from the chassis and remove the adapter from the I/O tray.

S002

CAUTION:
The power-control button on the device and the power switch on the power supply do not turn off the
electrical current supplied to the device. The device also might have more than one power cord. To
remove all electrical current from the device, ensure that all power cords are disconnected from the
power source.

” on page 89 “

CAUTION:
Make sure that all server power cords are disconnected from their power sources before performing
this procedure.

Before you remove a LOM adapter from slot 9:

1. Disconnect and label all cables connected to adapters in the I/O tray; then, remove the I/O tray. See

“Remove the I/O tray” on page 152.

2. Remove the riser for slot 10 to 15 (riser 2) to access the adapter connectors in the I/O tray. See “Remove

the riser for slot 10 to 15 (riser 2)” on page 213.

Complete the following steps to remove a LOM adapter from slot 9.

Watch the procedure

. A video of the installation process is available:

•

•

.

Hardware replacement procedures

95

«
...
103
104
105
106
107
...
»

Содержание ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkAgile VX 4-Socket 4U Certified Node

Бренд: Galleon Страницы: 47

Бренд: Digital Equipment Страницы: 73

Бренд: IEI Technology Страницы: 34

Бренд: Altos Страницы: 93

Silex Pricom SX-2000U2

Бренд: Silex technology Страницы: 1

Бренд: Fujitsu Страницы: 280

Бренд: D-Link Страницы: 113

Бренд: D-Link Страницы: 100

Бренд: QNAP Страницы: 16

Бренд: Tekron Страницы: 31

Бренд: Tekron Страницы: 32

Бренд: VVDN Страницы: 24

Бренд: Tatung Страницы: 35

Бренд: IBM Страницы: 24

Бренд: GIGA-BYTE TECHNOLOGY Страницы: 96

Бренд: GIGA-BYTE TECHNOLOGY Страницы: 99

Бренд: GIGA-BYTE TECHNOLOGY Страницы: 142

Бренд: AMX Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды