Lenovo ThinkAgile VX 4-Socket 4U Certified Node Скачать руководство пользователя страница 180

Страница: 180 / 296

Memory air baffle replacement

Use the following procedures to replace a memory air baffle.

Remove a memory baffle

Memory air baffles are in the system boards that are accessed from the front of the server.

Before you remove a memory air baffle:

1. Remove the front cover. See “Remove the front cover” on page 131.
2. Remove the compute tray where the system board and memory air baffles are installed. See “Remove a

compute tray” on page 115.

3. If you are removing a memory air baffle from the lower compute system board, remove the upper system

board or system board filler. See “Remove a system board” on page 109.

Complete the following steps to remove a memory air baffle.

Watch the procedure

. A video of the replacement process is available:

•

YouTube

•

Youku

Note:

Each memory air baffle spans six memory modules.

Step 1. Open the six pairs of memory module connector retaining clips that span the memory air baffle.

170

User Guide for ThinkAgile VX7820 Appliance, ThinkAgile VX 4-Socket 4U Certified Node

Содержание ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Результаты поиска

Содержание ThinkAgile VX 4-Socket 4U Certified Node

Отзывы:

Lenovo ThinkAgile VX 4-Socket 4U Certified Node, Руководство пользователя, Страница: 180 / 296

Результаты поиска

Содержание ThinkAgile VX 4-Socket 4U Certified Node

Отзывы: