Lenovo ThinkAgile VX 4-Socket 4U Certified Node Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 296

background image

Fan replacement

Use the following procedures to remove and install a fan. Fans are at the front of the server behind the front

cover.

Two types of fans are supported:

• 60 mm x 38mm, 16K internal hot-swap fans (01CX965)
• 60 mm x 38mm, 19K internal hot-swap fans (01PG490)

Notes:

• Different fan types cannot be mixed within a system. All fans must be either 16K fans or 19K fans.
• Before upgrading fans from 16K to 19K, you must make sure that the system has version 2 of the

ThinkSystem 2-CPU, 24-DIMM, Compute System Board (01CV978) installed in each compute tray.

Remove a fan

Press the fan handle inward toward the center of the server to release the latch; then, pull the fan forward

halfway, and wait 10 seconds before pulling the fan out of the server. Fans are hot-swap devices that can be

removed while the server is powered on.

S017

CAUTION:
Hazardous moving fan blades nearby. Keep fingers and other body parts away.

Before you remove a fan, remove the front cover. See “Remove the front cover” on page 131.

Complete the following steps to remove a fan:

Watch the procedure

. A video of the replacement process is available:

•

•

.

Hardware replacement procedures

119

«
...
127
128
129
130
131
...
»

Содержание ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkAgile VX 4-Socket 4U Certified Node

BladeCenter JS20

Бренд: IBM Страницы: 132

E7210 Master-FARM

Бренд: MSI Страницы: 34

SUPERSERVER 5018D-MF

Бренд: Supero Страницы: 120

SUPERSERVER 1018D-73MTF

Бренд: Supero Страницы: 124

Lynx DSS L106-S2 EX

Бренд: Westermo Страницы: 28

Rackmount 5000 Series

Бренд: Johnson Controls Страницы: 42

Бренд: QNAP Страницы: 39

Бренд: EVS Страницы: 198

Бренд: Black Box Страницы: 60

RF-ENCO-IP-HDSDI-35

Бренд: RFoG Страницы: 67

Бренд: Optibase Страницы: 28

Бренд: Intel Страницы: 233

Бренд: Lantronix Страницы: 73

Бренд: Inspur Страницы: 51

Бренд: Stentofon Страницы: 68

Бренд: Xblue Networks Страницы: 17

Бренд: Gigabyte Страницы: 100

Бренд: Aaeon Страницы: 110

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды