Lenovo ThinkAgile VX 4-Socket 4U Certified Node Скачать руководство пользователя страница 48

Страница: 48 / 296

Figure 23. Slot 16 to 17 riser connectors

Table 18. Slot 16 to 17 riser connectors

Callout

PCIe3 x8 (Slot 16)

PCIe3 x8 (Slot 17)

Storage interposer connectors

The following illustration shows the internal connectors on the interposer.

Note:

Some cable connectors have locks or latches that must be disengaged to disconnect the cable.

For information about interposer cable routing, see “Cable routing for drives” on page 45.

Figure 24. Storage interposer connectors

Table 19. Storage interposer connectors

Callout

PCIe SAS interface from system board (PCIE) (SAS

only)

Power for drive to backplane 2 or 5 (BP 2/5)

Drive power from system board (POWER)

PCI connector to RAID card

Drive signal from system board (SIDEBAND)

Power for drive to backplane 3 or 4 (BP 3/4)

Power for drive to backplane 1 or 6 (BP 1/6)

RAID card connectors

The following illustration shows the internal connectors on the RAID card.

There are two basic RAID card configurations.

Notes:

• The RAID cards in the illustration might be different than the RAID card in your system. Connector

locations for all RAID cards are similar.

User Guide for ThinkAgile VX7820 Appliance, ThinkAgile VX 4-Socket 4U Certified Node

Содержание ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Результаты поиска

Содержание ThinkAgile VX 4-Socket 4U Certified Node

Отзывы:

Похожие инструкции для ThinkAgile VX 4-Socket 4U Certified Node

Бренды по названию

Популярные бренды

Lenovo ThinkAgile VX 4-Socket 4U Certified Node, Руководство пользователя

Результаты поиска

Содержание ThinkAgile VX 4-Socket 4U Certified Node

Отзывы:

Похожие инструкции для ThinkAgile VX 4-Socket 4U Certified Node

Бренды по названию

Популярные бренды