Lenovo ThinkAgile VX 4-Socket 4U Certified Node Скачать руководство пользователя страница 50

Страница: 50 / 296

• SAS/NVMe drive backplane connectors

For information about drive backplane cable routing, see “Cable routing for drives” on page 45.

SAS drive backplane connectors

Figure 27. SAS drive backplane connectors

Table 22. SAS drive backplane connectors

Callout

Drive connector for SAS drives 0, 4, 8, 12, 16, and 20

Drive connector for SAS drives 3, 7, 11, 15, 19, and 23

Drive connector for SAS drives 2, 6, 10, 14, 18, and 22

SAS signal from RAID card

Drive connector for SAS drives 1, 5, 9, 13, 17, and 21

Backplane power from interposer

SAS/NVMe drive backplane connectors

Figure 28. SAS/NVMe drive backplane connectors

Table 23. SAS/NVMe drive backplane connectors

Callout

Drive connector for SAS or NVMe drives 0, 4, 8, 12, 16,

and 20

NVMe signal from compute board or storage tray

Drive connector for SAS or NVMe drives 2, 6, 10, 14,

18, and 22

SAS signal from RAID card

Drive connector for SAS drives 1, 5, 9, 13, 17, and 21

Backplane power from interposer

Drive connector for SAS drives 3, 7, 11, 15, 19, and 23

Internal cable routing

Some of the components in the server have internal cables and cable connectors.

User Guide for ThinkAgile VX7820 Appliance, ThinkAgile VX 4-Socket 4U Certified Node

Содержание ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Результаты поиска

Содержание ThinkAgile VX 4-Socket 4U Certified Node

Отзывы:

Похожие инструкции для ThinkAgile VX 4-Socket 4U Certified Node

Бренды по названию

Популярные бренды

Lenovo ThinkAgile VX 4-Socket 4U Certified Node, Руководство пользователя

Результаты поиска

Содержание ThinkAgile VX 4-Socket 4U Certified Node

Отзывы:

Похожие инструкции для ThinkAgile VX 4-Socket 4U Certified Node

Бренды по названию

Популярные бренды