Lenovo 7D1J Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 246

background image

Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID:
CIM Prefix: PLAT CIM ID: 0141

User Action:

Information only; no action is required.

•

FQXSPMA2010I: [PhysicalMemoryElementName] on Subsystem [MemoryElementName] is no

longer Throttled.

This message is for the use case when an implementation has detected Memory is no longer Throttled.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID:
CIM Prefix: PLAT CIM ID: 0143

User Action:

Complete the following steps:

1. If the compute node has recently been installed, moved, serviced, or upgraded, verify that the DIMM

is properly seated and visually verify that there is no foreign material in any DIMM connector on that
memory channel. If either of these conditions is found, correct and retry with the same DIMM. (Note:
The event Log might contain a recent FQXSFMA0011I event denoting detected change in DIMM
population that could be related to this problem.)

2. If no problem is observed on the DIMM connectors or the problem persists, replace the DIMM

identified by LightPath and/or event log entry.

3. If problem recurs on the same DIMM connector, replace the other DIMMs on the same memory

channel.

4. Check Lenovo support site for an applicable service bulletin or firmware update that applies to this

memory error.

5. If problem recurs on the same DIMM connector, inspect connector for damage. If damage found or

problem persists, collect Service Data log.

6. Contact Lenovo Support.

•

FQXSPMA2012I: An Over-Temperature Condition has been removed on the

[PhysicalMemoryElementName] on Subsystem [MemoryElementName].

This message is for the use case when an implementation has detected an Over Temperature Condition
for Memory that has been Removed.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: Critical - Temperature
SNMP Trap ID: 0
CIM Prefix: PLAT CIM ID: 0147

User Action:

Information only; no action is required

•

FQXSPMA2013I: The System [ComputerSystemElementName] has detected a POST Error

deassertion.

XClarity Controller events

95

«
...
97
98
99
100
101
...
»

Содержание 7D1J























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7D1J

Бренд: IBM Страницы: 908

Flex System x440 Compute Node

Бренд: IBM Страницы: 584

Бренд: Omega Страницы: 49

Бренд: Iwatsu Страницы: 338

Бренд: IBM Страницы: 66

Бренд: Ubiquiti Страницы: 28

Бренд: Intel Страницы: 32

Бренд: Avaya Страницы: 84

Бренд: Fujitsu Страницы: 200

Compaq AlphaServer DS10

Бренд: HP Страницы: 43

Cluster Platform Hardware Kits v2010

Бренд: HP Страницы: 12

Бренд: HP Страницы: 12

hpe proliant dl20 gen9

Бренд: HP Страницы: 131

Cisco MDS 8/12c

Бренд: HP Страницы: 44

Cluster Platform

Бренд: HP Страницы: 74

Cisco MDS 8/24c

Бренд: HP Страницы: 44

Cluster Platform

Бренд: HP Страницы: 88

HPE ProLiant DL180 Gen10

Бренд: HP Страницы: 157

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды