Lenovo 7D1J Скачать руководство пользователя страница 18

Страница: 18 / 246

•

0201020C: SMM2 Brd 5V: Voltage sensor, critical event was asserted, reading value %V (Threshold

%V)

Asserted when voltage sensed on 5V power rail is lower than lower critical threshold.

Severity: Error
Alert Category: System - SMM2 system event
SNMP Trap ID: 33620492

User Action:

1. Virtual reset SMM2 via Web GUI or IPMI command.

2. If the event persists, ensure all populated compute nodes are completely power off, then reseat

SMM2 module. (Service technician only)

3. If the event persists, ensure all populated compute nodes are completely power off, then replace the

SMM2 module. (Service technician only)

4. If the event persists, please consult with technical service.

•

0201020D: SMM2 Brd 12V: Voltage sensor, critical event was asserted, reading value %V

(Threshold %V)

Asserted when voltage sensed on 12V power rail is lower than lower critical threshold.

Severity: Error
Alert Category: System - SMM2 system event
SNMP Trap ID: 33620493

User Action:

1. Virtual reset SMM2 via Web GUI or IPMI command.

2. If the event persists, ensure all populated compute nodes are completely power off, then reseat

SMM2 module. (Service technician only)

3. If the event persists, ensure all populated compute nodes are completely power off, then replace the

SMM2 module. (Service technician only)

4. If the event persists, please consult with technical service.

•

0201020E: SMM2 Brd VBAT: Voltage sensor, critical event was asserted, reading value %V

(Threshold %V)

Asserted when voltage sensed on coin battery output voltage is lower than lower critical threshold.

Severity: Error
Alert Category: System - SMM2 system event
SNMP Trap ID: 33620494

User Action:

1. Virtual reset SMM2 via Web GUI or IPMI command.

2. If the event persists, ensure all populated compute nodes are completely power off, then reseat

SMM2 module. (Service technician only)

3. If the event persists, ensure all populated compute nodes are completely power off, then replace the

coin battery on the SMM2 module. (Service technician only)

4. If the event persists, ensure all populated compute nodes are completely power off, then replace the

SMM2 module. (Service technician only)

5. If the event persists, please consult with technical service.

•

02010708: SMM2 Brd 1.15V: Voltage sensor, warning event was asserted, reading value %V

(Threshold %V)

Asserted when voltage sensed on 1.15V power rail is higher than high non-critical threshold.

ThinkSystem DA240 Enclosure and ThinkSystem SD630 V2 Compute Node Messages and Codes Reference

Содержание 7D1J























































































































































































































































Результаты поиска

Содержание 7D1J

Отзывы:

Похожие инструкции для 7D1J

Бренды по названию

Популярные бренды

Lenovo 7D1J, Справочник

Результаты поиска

Содержание 7D1J

Отзывы:

Похожие инструкции для 7D1J

Бренды по названию

Популярные бренды