Konica Minolta DRYPRO 771 Скачать руководство пользователя страница 51

Страница: 51 / 100

Ch.2 Unpacking and Installation

< 49 >

DRYPRO MODEL 771 INSTALLATION MANUAL Ver.1.00 2003.10

Make sure that the power breaker located in the
lower left of the jam release-port cover.

Connect the power cable to the outlet (3P) of the
facility.

OFF

Connect the power cable of the UPD to the
power connector located in the lower left of the rear
panel of DRYPRO 771.

Press and hold the operation switch located on the
upper left of the left cover.

• Initialization takes place, and message "FILM

EMPTY!!" is displayed alternately with "PRESS
RESET/OPEN" together with a beep sound

• Then install the films in the DRYPRO 771.

14x17 B S:000 Q:000.

PRESS RESET/OPEN

Alternately displayed

14x17 B S:000 Q:000.

FILM EMPTY!!

When 3P plug is not available, connect to the power outlet using a "3P-2P" adapter.

In this case, make sure that the GND wire of the adapter is grounded to the GND

terminal of the facility.

Do not connect the ether

cable at this point.

Ether cable should be

connected after completing

all settings necessary for

DRYPRO 771.

Turn on the power breaker located in the lower left
of the jam release-port cover.

OFF

2.6

Start Up

After completing the removal and installation of specified parts, start up the DRYPRO 771.

2.6.1 Turning ON the Power

Turn on the power of the DRYPRO 771.

Содержание DRYPRO 771





































































































Результаты поиска

Содержание DRYPRO 771

Отзывы:

Похожие инструкции для DRYPRO 771

Бренды по названию

Популярные бренды

Konica Minolta DRYPRO 771, Руководство по установке

Результаты поиска

Содержание DRYPRO 771

Отзывы:

Похожие инструкции для DRYPRO 771

Бренды по названию

Популярные бренды