Konica Minolta DRYPRO 771 Скачать руководство пользователя страница 20

Страница: 20 / 100

Ch.1 Before Installation

< 18 >

DRYPRO MODEL 771 INSTALLATION MANUAL Ver.1.00 2003.10

Front, Top and Right Sides

1.4

Part Names

The names of the DRYPRO 771 parts relevant to installation are set out below.

1) Operation Panel

3) Supply Tray

2) Front Cover

8) Power Breaker

5) Air Intake

4) Film Ejection Tray

1) Operation Panel

Used to carry out operational
procedures and make settings of
DRYPRO 771.
Additionally, messages are displayed on
this panel.

2) Front Cover

This cover may be opened to remove a
film when a jam occurs.

3) Supply Tray

Holds the film.

4) Film Ejection Tray

Printed film is ejected into this tray.

5) Air Intake (2 locations)

Intakes air for internal cooling.

6) Right Cover

7) Front Cover Unlock Cover

Cover for the front cover unlock.

8) Power Breaker

Used for ON/OFF control of the main
power supply.

9) Stand

6) Right Cover

7) Front Cover

Unlock Cover

Содержание DRYPRO 771





































































































Результаты поиска

Содержание DRYPRO 771

Отзывы:

Похожие инструкции для DRYPRO 771

Бренды по названию

Популярные бренды

Konica Minolta DRYPRO 771, Руководство по установке

Результаты поиска

Содержание DRYPRO 771

Отзывы:

Похожие инструкции для DRYPRO 771

Бренды по названию

Популярные бренды