Keysight 4000 X-Series Скачать руководство пользователя страница 118

Страница: 118 / 170

118

4000 X-Series Oscilloscopes Advanced Training Guide

Serial Bus Decoding & Triggering, Search & Navigation, and Segmented Acquisition Labs

Lab #20: Decoding, Triggering, and Searching on I

S Serial Bus

Signals

In this lab you will learn how to set up the scope to decode and trigger on the I

(audio) serial bus traffic. In addition, you will learn how to use the scope’s

automatic I

S Search & Navigation capability, as well as Segmented Memory

acquisition. This lab does not provide a tutorial on the I

S protocol and signaling.

To complete this lab, your scope must be licensed with the I

S trigger and decode

option (Option AUDIO), as well as the MSO option. You can verify the installed

options on your oscilloscope at

[Help] > About Oscilloscope

Press

[Default Setup]

on the scope’s front panel.

Press

[Help]

; then tap the

Training Signals

softkey.

From the

Training Signals

menu, select and enable the

signal.

Press the

[1]

front panel key two times to turn off channel-1.

Press the

[Digital]

front panel key to turn on the digital channels of acquisition.

Tap the

Turn off D7-D0

softkey to turn off the lower 8 digital channels.

Tap the

Turn off D15-D9

softkey to turn off the upper 8 digital channels.

Tap the

Channel

softkey.

Double-tap

to turn on D9.

Repeat Step #9 to also turn on D8 and D7.

Set the scope’s timebase to

500.0 µs/div

Содержание 4000 X-Series











































































































































































Результаты поиска

Содержание 4000 X-Series

Отзывы:

Похожие инструкции для 4000 X-Series

Бренды по названию

Популярные бренды

Keysight 4000 X-Series, Руководство по продвинутой подготовке

Результаты поиска

Содержание 4000 X-Series

Отзывы:

Похожие инструкции для 4000 X-Series

Бренды по названию

Популярные бренды