Keysight 4000 X-Series Скачать руководство пользователя страница 19

Страница: 19 / 170

Oscilloscope Familiarization Labs

4000 X-Series Oscilloscopes Advanced Training Guide

and 80% threshold levels, or perhaps relative to absolute voltage levels, such as

from/to ± 1.0 V. Let’s now set up our scope to measure just the rise time of this

pulse relative to the 20% and 80% threshold levels.

Press the

Clear Meas

softkey; then press the

Clear All

softkey.

Press the

Settings

softkey; then press the

Thresholds

softkey.

Press the

Lower

softkey; set the value to

20%

Press the

Upper

softkey; set the value to

80%

To return to the previous menu, press the (Back) front panel key (just above

the power switch).

Press the (Back) key again because we descended two levels into this menu.

Press the

Rise

measurement on the right of the display; select

Track with Cursors

Using these user-defined measurement threshold levels (20% and 80%), our rise

time measurement should be faster because we are now measuring across a

shorter segment of the waveform as shown in

Figure 6

. The measurement should

now read approximately 30 ns. When we used the scope’s default 10%/90%

threshold levels, the measurement should have read approximately 40 ns.
Let’s now make one more measurement before completing this lab. But this time

let’s perform a more comprehensive set of measurements on this waveform.

Figure 6

Performing a rise time measurement relative to 20% and 80% threshold levels.

Back

Содержание 4000 X-Series











































































































































































Результаты поиска

Содержание 4000 X-Series

Отзывы:

Похожие инструкции для 4000 X-Series

Бренды по названию

Популярные бренды

Keysight 4000 X-Series, Руководство по продвинутой подготовке

Результаты поиска

Содержание 4000 X-Series

Отзывы:

Похожие инструкции для 4000 X-Series

Бренды по названию

Популярные бренды