Keysight 4000 X-Series Скачать руководство пользователя страница 59

Страница: 59 / 170

Advanced Triggering, Search & Navigation, and Segmented Acquisition Labs

4000 X-Series Oscilloscopes Advanced Training Guide

At this timebase setting (200 µs/div), the scope captured over a thousand edges of

this signal. And using the search conditions we entered (rising edges that exceed

100 ns), the scope should have just found approximately 10 violation edges as

shown in

Figure 34

. The white triangle marks at the top of the display indicate the

location of each “found” violation. Let’s now “navigate” to each of these detected

violations.

Press the

(zoom) front panel key.

Press the

and

navigation keys to navigate to each discovered edge

violation.

Let’s now use the scope’s Segmented Memory mode of acquisition to capture 500

consecutive occurrences of this edge transition violation. But to complete the rest

of this lab your scope must be licensed with the Segmented Memory option.
Press the (zoom) front key to turn off the scope’s horizontal zoom mode.

Push the horizontal position/delay knob to re-position the trigger point back to

center-screen.

Set the scope’s timebase to

100.0 ns/div

Press the

[Run/Stop]

front panel to begin repetitive acquisition again.

Press the

[Acquire]

front panel key.

Figure 34

The scope automatically finds several rise time violation edges.

Содержание 4000 X-Series











































































































































































Результаты поиска

Содержание 4000 X-Series

Отзывы:

Похожие инструкции для 4000 X-Series

Бренды по названию

Популярные бренды

Keysight 4000 X-Series, Руководство по продвинутой подготовке

Результаты поиска

Содержание 4000 X-Series

Отзывы:

Похожие инструкции для 4000 X-Series

Бренды по названию

Популярные бренды