Keysight 4000 X-Series Скачать руководство пользователя страница 16

Страница: 16 / 170

4000 X-Series Oscilloscopes Advanced Training Guide

Oscilloscope Familiarization Labs

Delta readouts are displayed on the right-hand side of the display. If you the press

the

[Cursors]

front panel key, you can see absolute voltage and time readouts for

each cursor near the bottom of the display. Your screen should now look similar to

Figure 3

In addition to using the scope’s default “manual” placement of time and voltage

cursors independently, you can also select the

Track Waveform

cursor mode by

pressing the

[Cursors]

front panel key, and then change from “manual” to

“tracking”. In the “tracking” cursor mode, you have the ability to control the time

placement of the cursors, and then the scope will automatically position the

voltage cursors on the waveform where the time cursors intersect the waveform.
Let’s now perform some automatic parametric measurements on this waveform.

Press the

[Meas]

front panel key (next to the Cursors knob).

If beginning with a default setup (as we have done), when the

[Meas]

key is

pressed the scope will turn on an automatic frequency and Vp-p measurement.

Because this scope is able to show up to four continuously updated

measurements, let’s add more measurements.

Press the

Type

softkey; then select

Maximum

Notice the level indicator that shows where this measurement is being

performed.

Figure 3

Using the scope’s cursor measurements.

Содержание 4000 X-Series











































































































































































Результаты поиска

Содержание 4000 X-Series

Отзывы:

Похожие инструкции для 4000 X-Series

Бренды по названию

Популярные бренды

Keysight 4000 X-Series, Руководство по продвинутой подготовке

Результаты поиска

Содержание 4000 X-Series

Отзывы:

Похожие инструкции для 4000 X-Series

Бренды по названию

Популярные бренды