Keysight 4000 X-Series Скачать руководство пользователя страница 28

Страница: 28 / 170

4000 X-Series Oscilloscopes Advanced Training Guide

Oscilloscope Familiarization Labs

Press the

[Cursors]

front panel key (near the Cursors knob).

Press the

Source

softkey and change the

Source

from channel-1 to

Math: f(t)

Push the Cursors knob and select the

cursor.

Move the X1 cursor so that it is on top of the highest frequency peak (near the

left side of the display).

On the right of the screen, select the

cursor.

Move the X2 cursor until it is on top of the 2nd highest frequency peak.

The frequencies at the X1 and X2 cursor locations are displayed near the bottom of

the scope’s display.
Let’s now verify the fundamental frequency of this signal using the scope’s

“counter” measurement.

Press the

[Meas]

front panel key.

Press the

Type

softkey and select

Counter

The “counter” measurement measures the average frequency over a fixed gate

time to provide a very high resolution (5 digits) measure of frequency, similar to a

standalone counter. But the measurement requires that the input signal be

repetitive.
The “frequency” measurement measures the period of just one cycle of the signal,

and then computes the frequency by taking the reciprocal.

Содержание 4000 X-Series











































































































































































Результаты поиска

Содержание 4000 X-Series

Отзывы:

Похожие инструкции для 4000 X-Series

Бренды по названию

Популярные бренды

Keysight 4000 X-Series, Руководство по продвинутой подготовке

Результаты поиска

Содержание 4000 X-Series

Отзывы:

Похожие инструкции для 4000 X-Series

Бренды по названию

Популярные бренды