Keysight 4000 X-Series Скачать руководство пользователя страница 8

Страница: 8 / 170

4000 X-Series Oscilloscopes Advanced Training Guide

Getting Started

Front Panel Overview

For instant help on any topic, press and hold any key, softkey, or knob.

Run Control

When the oscilloscope is turned on, or if

[Auto Scale]

is pressed, the acquisition

will be set to

[Run]

. At any time you may

[Stop]

the acquisition process to examine

a signal in detail or to save it.

• The

[Default Setup]

key on the front panel sets the oscilloscope to the default

configuration.

Because the oscilloscope may have been used in a variety of applications by a

variety of people, it is a good measurement procedure to put the oscilloscope in

a known starting mode (Default Setup). This makes it easy to duplicate

measurements because no special conditions are set.

• The

[Auto Scale]

key on the front panel automatically configures the

oscilloscope by analyzing all active channels, turning them on and setting the

timebase, V/div, and trigger conditions for an initial display.

• Press the

[Single]

key to make a single acquisition and stop the acquisition

process.

Waveform Controls

• The

[Analyze]

key sets trigger levels, measurement threshold levels, video

trigger auto setup and display, or the mask testing application options.

• The

[Acquire]

key on the front panel lets you set the oscilloscope data

acquisition modes.

Содержание 4000 X-Series











































































































































































Результаты поиска

Содержание 4000 X-Series

Отзывы:

Похожие инструкции для 4000 X-Series

Бренды по названию

Популярные бренды

Keysight 4000 X-Series, Руководство по продвинутой подготовке

Результаты поиска

Содержание 4000 X-Series

Отзывы:

Похожие инструкции для 4000 X-Series

Бренды по названию

Популярные бренды