KEPCO BOP-GL 1KW Скачать руководство пользователя страница 79

Страница: 79 / 174

BOP-1K-GL 111315

3-15

3.3.9

SETTING MAIN CHANNEL MODE (VOLTAGE OR CURRENT)

When the unit is turned on, the main channel mode is determined by the power-up switches.

•

If S3 is set to 00000 the mode is determined by the status of pin 2 of the Analog I/O port

(see Table 2-12). Applying a TTL logic 1 (or open circuit) programs the unit to voltage
mode. Applying a TTL logic 0 (or short circuit) programs the unit to current mode.

•

If S3 is set to 0nnnn (where nnnn = binary number from 1 (0001, where S3-1 = 1) to 15

(1111), unit turns on with the mode previously saved in the selected location, and may be
either voltage or current mode.

•

If S3 is set to 1xxxn (xxx = set as desired; if n = 0, unit is set to current mode, if n = 1, unit

is set to voltage mode.

Once the unit is powered up, main channel mode can be controlled by the FUNC:MODE com-
mand (see PAR. B.45).

•

Sending FUNC:MODE VOLT sets the unit to voltage mode and sending FUNC:MODE

CURR sets the unit to current mode.

•

Sending FUNC:MODE EXT allows the mode to be determined by the status of pin 2 of

the Analog I/O port (see Table 2-12).

3.3.10

PROTECTION LIMITS

When the unit is turned on the protection limits are determined by the power-up switches:

•

If S3 is set to 00000 the protection limits are controlled by the pins 5, 6, 13 and 14 of the

Analog I/O port (see Table 2-12).

•

If S3 is set to 100xx (x = set as desired, S3-3 and S3-4 = 0, S3-5 = 1), the protection lim-

its are controlled by the pins 5, 6, 13 and 14 of the Analog I/O port (see Table 2-12).

•

If S3 is set to 0nnnn (where nnnn = binary number from 1 (0001, where S3-1 = 1) to 15

(1111), unit turns on with the limits previously saved in the selected location.

•

If S3 is set to 101xx (x = set as desired, S3-3 = 1, S3-4 = 0, S3-5 = 1), –V Protect Max

and –C Protect Max are internally set to maximum (1.01 x nominal (rated) values. +V
Protect Max and +C Protect Max are Internally set to min. (box).

•

If S3 is set to 110xx (x = set as desired, S3-3 = 0, S3-4 = 1, S3-5 = 1), +V Protect Max

and +C Protect Max are internally set to maximum (1.01 x nominal (rated) values. –V
Protect Max and –C Protect Max are Internally set to min. (box).

•

If S3 is set to 111xx (x = set as desired, S3-3 = 1, S3-4 = 1, S3-5 = 1), ±V Protect Max

and ±C Protect Max are internally set to maximum (1.01 x nominal (rated) values.

Once the unit is powered up, main channel mode can be controlled by the CURR:PROT:MODE
(see PAR. B.31) and VOLT:PROT:MODE (see PAR. B.98) commands.

•

Sending VOLT:PROT:MODE FIXED allows the voltage protect limits to be controlled by

VOLT:PROT:LIM commands and sending CURR:PROT:MODE FIXED allows the current
protect limits to be controlled by CURR:PROT:LIM commands

Содержание BOP-GL 1KW















































































































































































Результаты поиска

Содержание BOP-GL 1KW

Отзывы:

Похожие инструкции для BOP-GL 1KW

Бренды по названию

Популярные бренды

KEPCO BOP-GL 1KW, Руководство оператора

Результаты поиска

Содержание BOP-GL 1KW

Отзывы:

Похожие инструкции для BOP-GL 1KW

Бренды по названию

Популярные бренды