KEPCO BOP-GL 1KW Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 174

background image

BOP-1K-GL 111315

2-11

CAUTION: DO NOT repeatedly toggle the POWER circuit breaker/switch as this may

damage the unit.

5. Connect the power supply to source power (see PAR. 2.5.2). With no load connected, set

POWER switch to the ON position.

6. Each time the unit is turned on an internal self-test is performed. If the unit passes, it initial-

izes with the power-up settings established in step 1 and the front panel POWER/FAULT/
LIMIT light is green (power good), the DIGITAL CONTROL light is not lit (analog input
enabled) and the VOLTAGE/CURRENT light is green (voltage mode), MASTER/SLAVE light
is green (standalone or master configuration) and the OUTPUT ON light is lit (output
enabled). If the front panel POWER/FAULT/LIMIT light is red, the unit has failed self-test;
contact Kepco for further instructions. If the unit beeps, or the MASTER/SLAVE or VOLT-
AGE/CURRENT light blinks, refer to PAR. 3.8 for troubleshooting.

7. Send the following SCPI commands:

*IDN?

The unit responds with model number and serial number.

FUNC:MODE VOLT

Puts the unit in Voltage Mode.

VOLT:MODE FIX

Allows digital control of the output.

CURR:PROT:LIM xx

xx is the nominal current rating of the unit.

VOLT yy

yy is the nominal voltage rating of the unit.

OUTP ON

Enables the output.

MEAS:VOLT?

Measures output voltage and returns value to host computer.

8. Connect a digital voltmeter (DVM) (resolution and accuracy of 0.01% or better) to the

OUTPS and COMS terminals at the rear panel terminal block.

9. Verify DVM voltage reading matches the nominal voltage of the unit within 0.01% of rated

maximum voltage.

2.4

INSTALLATION

2.4.1

RACK MOUNTING

The unit is shipped with four feet attached to bottom of the unit which must be removed prior to
installation (see Figure 1-2). The BOP is designed to be rack mounted in a standard 19-inch
wide rack using the mounting ears (supplied) attached to the front panel (see Figure 1-2). Allow
a minimum of 1.0 in. (25.4 mm) in front of the unit to permit air intake necessary for proper cool-
ing of the unit.

CAUTION: The rack must provide support at the rear (within 6 inches of

the rear panel). Optional slides can also be used (see PAR. 2.4.2).

2.4.2

SLIDE INSTALLATION

Optional slides are available for rack mounting (see Table 1-5 and Figure 1-2).

«
...
47
48
49
50
51
...
»

Содержание BOP-GL 1KW















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BOP-GL 1KW

Бренд: Campbell Hausfeld Страницы: 8

Бренд: Parkside Страницы: 40

Бренд: hilmor Страницы: 12

Бренд: ITech Страницы: 46

Бренд: Milwaukee Страницы: 35

Бренд: Ryobi Страницы: 13

Бренд: OEM Tools Страницы: 8

Бренд: Kärcher Страницы: 68

Бренд: Dixon Automatic Tool Страницы: 11

Бренд: Far Tools Страницы: 52

Бренд: YOKOGAWA Страницы: 21

X-Finity Series

Бренд: Ultra Products Страницы: 1

Бренд: Power works Страницы: 136

COMFORT CRIMP SHURE STAKE ERG4811

Бренд: Thomas & Betts Страницы: 2

Бренд: Nitto Страницы: 14

Бренд: TET Electronics Страницы: 16

BC-RAD 14XA Select

Бренд: Christie Страницы: 17

COMPLETE ProGrade C-5016LMA

Бренд: AXXIS Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды