manualshive.com logo in svg

KEPCO BOP-GL 1KW, Руководство оператора

"KEPCO BOP-GL 1KW" - 1 кВт лабораторный источник питания с операторская инструкция для правильного использования. Бесплатное скачивание руководства для пользователя доступно на manualshive.com. Получите подробную информацию о продукте и его использовании, скачав руководство сейчас.

Поделиться
Скачать
background image

LIST OF FIGURES

FIGURE

TITLE

PAGE

viii

BOP-1K 111315

1-1

 High Power BOP-GL Series Power Supply...................................................................................................  x

1-2

 BOP-GL Power Supply, Outline Drawing ...................................................................................................  1-11

1-3

 BOP Output Characteristics .......................................................................................................................  1-16

2-1

 BOP-GL Series Rear Panel........................................................................................................................  2-1

2-2

 BOP-GL Top Cover Accessible Components ............................................................................................  2-3

2-3

 Factory Default Power-up Switch Settings .................................................................................................  2-10

2-4

 Load Connections, Local Sensing..............................................................................................................  2-16

2-5

 Load Connections, Remote Sensing..........................................................................................................  2-16

2-6

 Connections for Analog Control and Monitoring of BOP-GL Power Supply...............................................  2-18

2-7

 Parallel Configuration, Local Sensing, Typical ...........................................................................................  2-20

2-8

 Parallel Configuration, Remote Sensing, Typical .......................................................................................  2-21

2-9

 Series Configuration, Local Sensing, Typical.............................................................................................  2-22

2-10  Series Configuration, Remote Sensing, Typical.........................................................................................  2-23
2-11  Typical Master/Slave Protection Interconnections .....................................................................................  2-24
3-1

 BOP-GL Series Front Panel .......................................................................................................................  3-3

3-2

 Remote Shutdown Using External Power, Standalone or Multiple units....................................................  3-13

3-3

 Remote Shutdown Using Internal Power, Standalone Units ......................................................................  3-13

3-4

 Remote Shutdown Using Internal Power, Multiple Units,...........................................................................  3-13

3-5

 Remote On-Off, Standalone or Multiple Units ............................................................................................  3-14

3-6

 Programming Example to Verify Previous Command has Completed.......................................................  3-24

3-7

 Sample Waveform......................................................................................................................................  3-26

3-8

 RS 232 Implementation..............................................................................................................................  3-33

3-9

 Tree Diagram of SCPI Commands Used with BOP Power Supply ............................................................  3-41

3-10  Message Structure .....................................................................................................................................  3-45
3-11  Status Reporting Structure .........................................................................................................................  3-48
3-12  Typical Example Of BOP Power Supply Program Using SCPI Commands...............................................  3-51
4-1

 Calibration Setup in Voltage Mode.............................................................................................................  4-5

4-2

 Calibration Setup in Current Mode .............................................................................................................  4-8

A-1

 GPIB Commands ....................................................................................................................................... A-3

B-1

 Programming the Output ............................................................................................................................ B-3

B-2

 Using List Commands to measure sample at End of Pulse ....................................................................... B-5

B-3

 Using List Commands to measure sample at Start of Pulse ...................................................................... B-6

B-4

 Setting Limits.............................................................................................................................................. B-8

B-5

 Using LIST Commands and Queries.......................................................................................................... B-14

B-6

 Using LIST Commands for Sawtooth and Triangle Waveforms................................................................. B-21

B-7

 Using List:WAIT Commands to Control Generation of a Waveform Measured by

Multiple External Devices using a Single External Pulse ........................................................................ B-22

B-8

 Using List:WAIT Commands to allow an external device time to

function while imposing a maximum wait time......................................................................................... B-23

B-9

 Using List:WAIT Commands to Control Generation of a Waveform Measured by

Multiple External Devices using the Low-Going leading Edge of an External Pulse ............................... B-26

B-10  Using PROT:LIM:POS and PROT:LIM:POS Commands to Set Asymmetrical Limits ............................... B-29
B-11  Using Status Commands and Queries ....................................................................................................... B-33
B-12  Setting the Unit to Remote Mode via Serial (RS 232) Port ........................................................................ B-36
B-13  Using System Commands and Queries ..................................................................................................... B-37

Содержание BOP-GL 1KW















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BOP-GL 1KW

Earlex HG1200 Safety And Operating Instructions preview
HG1200
Бренд: Earlex Страницы: 4
Laser 8012 Instructions Manual preview
8012
Бренд: Laser Страницы: 8
Parkside 352083 2007 Original Instructions Manual preview
352083 2007
Бренд: Parkside Страницы: 78
Parkside PDSP 1000 A1 SANDBLASTER GUN Operation And Safety Notes Translation Of Original Operation Manual preview
PDSP 1000 A1 SANDBLASTER GUN
Бренд: Parkside Страницы: 51
Parkside PDT 40 A1 Operation And Safety Notes Original Operating Instructions preview
PDT 40 A1
Бренд: Parkside Страницы: 56
MGS HBM R3 Operating Manual preview
HBM R3
Бренд: MGS Страницы: 38
Artos CR.11 Owner'S Manual preview
CR.11
Бренд: Artos Страницы: 185
HELVAR Digidim 401 Manual preview
Digidim 401
Бренд: HELVAR Страницы: 2
Hama Cap Operating Instructions Manual preview
Cap
Бренд: Hama Страницы: 38
BSM Dahle 250 Instructions Manual preview
Dahle 250
Бренд: BSM Страницы: 96
P.I.T. PMT20H-035A User Manual preview
PMT20H-035A
Бренд: P.I.T. Страницы: 24
Wacker Neuson RD 27-100 Operator'S Manual preview
RD 27-100
Бренд: Wacker Neuson Страницы: 144
Parkside PLKA 3.6 A2 Original Instructions For Use preview
PLKA 3.6 A2
Бренд: Parkside Страницы: 2
Cleveland Steel Tool 55 Ton Manual preview
55 Ton
Бренд: Cleveland Steel Tool Страницы: 44
DAJ PEGD8016 User Manual preview
PEGD8016
Бренд: DAJ Страницы: 10
Yokota TKA111 Manual preview
TKA111
Бренд: Yokota Страницы: 8
U-Line Shrinkfast 975 Manual preview
Shrinkfast 975
Бренд: U-Line Страницы: 21
Harman Martin VC-Feeder User Manual preview
Martin VC-Feeder
Бренд: Harman Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды