KEPCO BOP-GL 1KW Скачать руководство пользователя страница 158 | Manualshive

Страница: 158 / 174

background image

B-24

BOP-1KW-GL 111315

B.79

[SOURce:]LIST:VOLT:APPLy COMMAND

LIST:VOLT:APPL

Syntax:

Short Form: LIST:VOLT:APPL <type>,<value1>,<value2>[,<value3>]
Long Form: LIST:VOLTage:APPLy <type>,<value1>,<value2>[,<value3>]
Where <type> is {SQUARE | RAMP+ | RAMP- | TRIANGLE | SINE | LEVEL}

<value1> is frequency in Hz; for LEVEL <value1> is period, duration in Seconds

<value2> is p-p amplitude (or amplitude (offset) for level) in Volts
<value3> is offset (optional, default is 0, not applicable to level) in Volts

Description:

Causes the unit to add a series of points to both the list:volt array and the list:dwell array to
make either a level or a waveform of one of five types.

Refer to table 3-6 for a description of the

waveform types. The waveform type specified is generated at the frequency specified with a peak-to-
peak amplitude centered on zero. If the optional offset value is specified, the center of the generated
series of points is moved off zero. The apply generator takes into account the soft limits for the voltage
channel and insures the generated array does not exceed the unit’s capabilities.

B.80

[SOURce:]LIST:VOLTage:APPLy:SWEep COMMAND

LIST:VOLT:APPL:SWE

Syntax:

Short Form: LIST:VOLT:APPL:SWE <>,
Long Form: LIST:VOLTage:APPLy:SWEep <value1>,<value2>
Where <value1> is start angle. Valid from 0 to 359.99 degrees.

<value2> is stop angle. Valid from 0.01 to 360.00 degrees

Description:

Allows the user to provide a starting angle for either triangle and sine waveforms and an

optional stop angle.

If the stop angle is not supplied, the unit defaults to 360 degrees. This command

should be placed at the beginning of the waveform program to be applicable to all sine and triangle
waveform segments.

B.81

[SOURce:]LIST:VOLTage:APPLy:SWEep? QUERY

LIST:VOLT:APPL:SWE?

Syntax:

Short Form: LIST:VOLT:APPL:SWE? Long Form: LIST:VOLTage:APPLy:SWEep?
Return Value: <value1>, <value2>(0.01 to 360)

Description:

Returns start

<value1>

and stop

<value2>

angle in degrees for either triangle and sine wave-

forms.

B.82

[SOURce:]LIST:VOLTage:POINts? QUERY

LIST:VOLT:POIN?

Syntax:

Short Form: LIST:VOLT:POIN? Long Form: LIST:VOLTage:POINts?
Return Value: <n> where n = number of points used

Description:

Identifies the total number of points in a list and the next location to be filled by LIST:VOLT
command.

The LIST:VOLT pointer is initially at 0 via LIST:CLE. For each data point entered by a

LIST:VOLT command the list pointer is incremented If LIST:VOLT:POIN? returns 5, the LIST:VOLT
pointer is at 5 indicating there are 5 data points comprising the list (locations 0 though 4) and location
5 is the next to be filled. If LIST:CURR has any entries, an error message: -221,”Settings conflict” is
posted in the error queue. Related Commands: LIST:VOLT. (See example, Figure B-5.)

«
...
156
157
158
159
160
...
»

Содержание BOP-GL 1KW















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BOP-GL 1KW

Бренд: Nation Flooring Equipment Страницы: 2

Бренд: Narex Страницы: 16

Бренд: NARGESA Страницы: 71

Бренд: Pulsar Страницы: 8

Бренд: Metabo Страницы: 72

Бренд: Hakko Electronics Страницы: 2

Бренд: Energenie Страницы: 45

Бренд: H&H Страницы: 20

Бренд: Xtreme Страницы: 10

Watt Series Programmable DC Power Supply XG...

Бренд: Xantrex Страницы: 286

Бренд: National Flooring Equipment Страницы: 44

Бренд: Shell Страницы: 20

Бренд: Parkside Страницы: 35

Бренд: Ingersoll-Rand Страницы: 23

Бренд: Corsair Страницы: 10

Бренд: nextys Страницы: 5

Бренд: multicomp pro Страницы: 4

Бренд: Parkside Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды