manualshive.com logo in svg

KEPCO BOP-GL 1KW, Руководство оператора

"KEPCO BOP-GL 1KW" - 1 кВт лабораторный источник питания с операторская инструкция для правильного использования. Бесплатное скачивание руководства для пользователя доступно на manualshive.com. Получите подробную информацию о продукте и его использовании, скачав руководство сейчас.

Поделиться
Скачать
background image

B-8

BOP-1KW-GL 111315

B.20

[SOURce:]CURRent[:LEVel][:IMMediate][:AMPlitude] QUERY 

CURR?

Syntax:

Short Form: [SOUR:]CURR[:LEV][:IMM][:AMP]? MIN, MAX
Long Form: [SOURce:]CURRent[:LEVel][:IMMediate][:AMPlitude]? MIN, MAX

Return Value:

<exp_value> = digits with decimal point and Exponent, e.g., 2.71E1 for 27.1

Description:

Returns either the programmed value, maximum value, or minimum value of current. 

The

CURR? query returns the programmed value of current. Actual output current will depend on load con-
ditions. The CURR?MAX query returns the maximum positive current allowed for a particular model.
CURR? MIN returns minimum negative current allowed for power supply (always negative).

 Related

Commands:

 CURR. (See example, Figure B-1.)

B.21

[SOURce:]CURRent[:LEVel]:LIMit[:BOTH] COMMAND 

CURR:LIM[:BOTH]

Syntax:

Short Form: [SOUR:]CURR[:LEV]:LIM[:BOTH] <value>
Long Form: [SOURce:]CURRent[:LEVel]:LIMit[:BOTH] <value>
where <value> is between zero and I

NOM

Description: Establishes the software limit <value> for output current, i.e., sets the maximum value of output cur-

rent that the unit will be allowed to source and sink. Requires MEM:UPD (PAR. B.12) to save for
power up. See PAR. 3.5.5.2 and Figure 3-6 for special programming considerations. (See Figure B-4)

FIGURE B-4.    SETTING LIMITS

NOTES: 1. This example assumes a BOP 36-28GL power supply is operating in constant current (CC) mode.

2 Examples below are intended only to illustrate command functions. Refer to PAR.  for program-

ming techniques to optimize performance.

CURR:LIM?

Returns 28,28 (positive and negative defaults for max 
current in current mode).

CURR:LIMIT:POS 10;NEG 2

Establishes the maximum positive and negative current values
that can be set in current mode.

FUNC:MODE VOLT

SETS POWER SUPPLY IN VOLTAGE MODE.

VOLT 15;CURR 2

Allows the power supply to provide 15 volts positive with the 
ability to source or sink up to 2 amperes. The display shows:
 15.000 2.000 2.000.

CURR 10

Since the BOP is operating in voltage mode, sets the current 
capability (current protect) to 10 amperes.The display shows:
 15.000 10.000 10.000

CURR:PROT?

Returns 10,10 

CURR:PROT:NEG 1

Limits the negative current capability to 1 ampere.

CURR:PROT:LIM:NEG 5

Prevents CURR:PROT:NEG setting from exceeding
5 amperes 

CURR:PROT?

Returns 10,1 (the actual positive (10) and negative (1) 
protection levels for the current.

                                   ---- Turn BOP power off and then on.
CURR:LIM?

Returns 28,28 the factory default levels (all the above
changes have been lost). To save the changed limits for power-
up, the user must send MEM:UPD LIM.

CURR:PROT:LIM:POS 28.3;NEG 28

Establishes new max current protect limits (positive 28.3 and
 negative 28.

CURR 28

Establishes the positive protect to be 28 amperes and the 
negative protection remains 28 amperes.

CURR:PROT?

returns 28,28

FUNC:MODE CURR

Changes the mode of operation of the power supply to current
 mode.

Содержание BOP-GL 1KW















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BOP-GL 1KW

YIHUA 302D Operation Instruction preview
302D
Бренд: YIHUA Страницы: 2
Valex P2000 Instructions For Use And Safety Instructions preview
P2000
Бренд: Valex Страницы: 8
TDK-Lambda PFE300SA Series Instruction Manual preview
PFE300SA Series
Бренд: TDK-Lambda Страницы: 19
Status C16-2Li Original Instructions Manual preview
C16-2Li
Бренд: Status Страницы: 22
Ubiquiti EdgePower 54V Quick Start Manual preview
EdgePower 54V
Бренд: Ubiquiti Страницы: 19
Ubermann UJS04BRA Operator'S Manual preview
UJS04BRA
Бренд: Ubermann Страницы: 40
ersa Multi-TC Operating Instructions preview
Multi-TC
Бренд: ersa Страницы: 4
Rockwell Automation 1606-XLEDNET3 Instruction Manual preview
1606-XLEDNET3
Бренд: Rockwell Automation Страницы: 4
Eastwood 13650 Instructions preview
13650
Бренд: Eastwood Страницы: 3
Band-it C00169 Operating Instructions preview
C00169
Бренд: Band-it Страницы: 4
Chicago Pneumatic CP 1230 SPDR Safety And Operating Instructions Manual preview
CP 1230 SPDR
Бренд: Chicago Pneumatic Страницы: 196
Neilsen CT5673 Instruction Manual preview
CT5673
Бренд: Neilsen Страницы: 16
Baileigh Industrial HSP-176M-HD Operator'S Manual preview
HSP-176M-HD
Бренд: Baileigh Industrial Страницы: 44
Greatneck 80122 Owner'S Manual preview
80122
Бренд: Greatneck Страницы: 17
Qonnect AS N-12-R Operating Instructions preview
AS N-12-R
Бренд: Qonnect Страницы: 4
ASTRO TOOL Corp. 10692 Manual preview
10692
Бренд: ASTRO TOOL Corp. Страницы: 2
Deprag 347-218-31 Operating Instruction Booklet preview
347-218-31
Бренд: Deprag Страницы: 40
HellermannTyton KR8PNSE Operating Instructions preview
KR8PNSE
Бренд: HellermannTyton Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды