KEPCO BOP-GL 1KW Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 174

background image

3-36

BOP-1K-GL 111315

3.6.4.3.4 CONFIGURE PROMPT MODE

The prompt mode can be controlled using the SYST:COMM:SER:PROM command (see PAR.
B.130). (See PAR. 3.6.4.2.3 for a description of prompt mode). To save changes for subsequent
power-up cycles, send MEM:UPD:SER and tag unit with new revised power-up setting.

Enable

- Enables Serial Prompt (see PAR. 3.6.4.2.3 for a description of prompt mode).

Disable

- Disables Prompt. If both Serial XON/XOFF and Prompt functions are disabled, Echo

mode is the default (see PAR. 3.6.4.2.2 for a description of Xon/Xoff mode).

If both Serial Prompt (see PAR. 3.6.4.2.3) and Echo (see PAR. 3.6.4.2.2) modes. are enabled,
Prompt is returned when the unit is ready and any received characters are echoed back to the
sender.

3.6.5

BOP VISA INSTRUMENT DRIVER

The VISA instrument driver for the BOP power supply, available for download at www.kepco-
power.com/drivers.htm, simplifies programming with a VISA compatible GPIB controller.
Included are:

•

source code (C) for all VISA functions (kp_bophi.c)

•

a complete programming reference manual (kp_bophi.doc)

•

a sample application of the VISA functions (written in C) which can be used to program

one or more BOP power supplies using a virtual front panel observed on a com-
puter monitor (kp_appl.c)

Although the software drivers supplied by Kepco are VISA compliant, they also require the
installation of the proper VISA driver from your GPIB card supplier. Many vendors supply this
software with the hardware; National Instruments (http://www.natinst.com) has the driver for
their cards available on the internet at a file transfer site (ftp://ftp.natinst.com — find the folder
for support and VISA drivers).

3.7

SCPI PROGRAMMING

SCPI (Standard Commands for Programmable Instruments) is a programming language con-
forming to the protocols and standards established by IEEE 488.2 (reference document

ANSI/IEEE Std 488.2, IEEE Standard Codes, Formats, Protocols, and Common Commands

). SCPI com-

mands are sent to the BOP Power Supply as ASCII output strings within the selected program-
ming language (PASCAL, BASIC, etc.) in accordance with the manufacturer’s requirements for
the particular GPIB controller card used.

Different programming languages (e.g., BASIC, C, PASCAL, etc.) have different ways of repre-
senting data that is to be put on the IEEE 488 bus. It is up to the programmer to determine how
to output the character sequence required for the programming language used. Address infor-
mation (GPIB address) must be included before the command sequence. (See PAR.3.6.3.1.1 to
establish the BOP Power Supply GPIB address.)

«
...
98
99
100
101
102
...
»

Содержание BOP-GL 1KW















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BOP-GL 1KW

Бренд: Palmgren Страницы: 12

Бренд: Mafell Страницы: 75

Бренд: Mafell Страницы: 46

MAG-8200 Series

Бренд: Magna-Matic Страницы: 38

Бренд: ENAR Страницы: 36

Бренд: Metabo Страницы: 68

Бренд: Hama Страницы: 40

Бренд: Zenit Страницы: 8

Бренд: phytron Страницы: 29

Бренд: Promac Страницы: 41

Бренд: Gardena Страницы: 14

Бренд: Agilent Technologies Страницы: 179

Бренд: Panamax Страницы: 45

Бренд: Hellermann Tyton Страницы: 8

Invitrogen PowerEase Touch PS0350

Бренд: Thermo Scientific Страницы: 38

Бренд: Swivelpole Страницы: 2

Бренд: Precision matthews Страницы: 29

Diamond Hone 100

Бренд: Chef's Choice Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды