KEPCO BOP-GL 1KW, Руководство оператора

Страница: 70 / 174

3-6
BOP-1K-GL 111315
changed (PAR. 3.3.5.1), the corresponding protect channel limit is automatically changed to be
5% of the nominal (rated) value above the user-programmed software limit.
TABLE 3-2. VOLTAGE AND CURRENT PARAMETER DEFINITIONS
Term Definition
To modify
refer to PAR.
+E
Onom
–E
Onom
The nominal (rated) output voltage of the unit determined by model; e.g. for
a BOP 36-28GL, ±E
Onom
is 36V.
N/A
+I
Onom
–I
Onom
The nominal (rated) output current of the unit determined by model; e.g. for
a BOP 36-28GL, ±I
Onom
is 28A.
N/A
+Voltage
–Voltage Voltage mode only. Positive (+) and negative (–) output voltage values
established by remote command.
Range (+): 0 to +Voltage max
Range (–): 0 to –Voltage min
B.86, B.96
+Voltage max
–Voltage min Voltage mode only. Maximum (positive) and minimum (maximum negative)
voltage that can be set.
Value (+): 0 to +E
Onom
Value (–): 0 to –E
Onom
B.88, B.89, B.90,
B.92
+Current Protect
–Current Protect Voltage mode only. Defines maximum (+) current and Minimum (maximum
negative) (–) that unit can source or sink.
Range (+): +Current Protect min to +Current Protect max
Range (–): –Current Protect max to –Current Protect min
B.29, B.30,
B.35, B.33, B.19
+Current Protect Max
–Current Protect Min Voltage mode only. Maximum setting for +Current Protect and Minimum
(maximum negative) setting for –Current Protect.
Value (+): +Current Protect min to (1.01 x +Current max)
Value (–): –Current Protect max to (1.01 x –Current min)
B.37, B.38, B.41,
B.39
Minimum (box)
+Current Protect Min
–Current Protect Max Voltage mode only. Minimum (positive) setting for +Current Protect and
maximum (maximum negative) setting for –Current Protect. Values of ±Cur-
rent Protect bCurrent Protect Min and –Current Protect Max (near
zero) are not allowed.This zone (also referred to as the
minimum (box) is
automatically calculated by the BOP (see Figure 1-3).
N/A
+Voltage Protect
–Voltage Protect Current mode only. Maximum positive (+) and minimum (maximum
negative) (–) voltage that can appear at the output.
Range (+): +Voltage Protect min to +Voltage Protect max
Range (–): –Voltage Protect max to –Voltage Protect min
B.96, B.97,
B.102, B.100,
B.86
+Voltage Protect Max
–Voltage Protect Min Current mode only. Maximum (positive) setting for +Voltage Protect and
Minimum (maximum negative) setting for –Voltage Protect.
Value (+): +Voltage Protect min to (1.01 x +Voltage max)
Value (–): –Voltage Protect max to (1.01 x –Voltage min)
B.104, B.105,
B.108, B.106
Minimum (box)
+Voltage Protect Min
–Voltage Protect Max Current mode only. Minimum (positive) setting for +Voltage Protect and
maximum (maximum negative) setting for –Voltage Protect. Values of ±Volt-
age Protect bVoltage Protect Min and –Voltage Protect Max (near
zero) are not allowed. This zone (also referred to as the
minimum (box) is
automatically calculated by the BOP (see Figure 1-3).
N/A
+Current
–Current Current mode only. Positive and negative output current established by
remote command.
Range (+): 0 to +Current max
Range (–): 0 to –Current min
B.19, B.29
+Current max
–Current min Current mode only. Maximum (positive) and minimum (maximum
negative) current that can be set.
Value (+): 0 to +I
Onom
Value (–): 0 to –I
Onom
B.21, B.25,
B.22