manualshive.com logo in svg

KEPCO BOP-GL 1KW, Руководство оператора

"KEPCO BOP-GL 1KW" - 1 кВт лабораторный источник питания с операторская инструкция для правильного использования. Бесплатное скачивание руководства для пользователя доступно на manualshive.com. Получите подробную информацию о продукте и его использовании, скачав руководство сейчас.

Поделиться
Скачать
background image

BOP-1K 111315

i

TABLE OF CONTENTS

SECTION

PAGE

SECTION 1 -  INTRODUCTION

1.1

 Scope of Manual ..................................................................................................................................... 1-1

1.2

 General Description................................................................................................................................. 1-1

1.3

 Specifications .......................................................................................................................................... 1-1

1.4

 Remote Control ....................................................................................................................................... 1-13

1.5

 Features .................................................................................................................................................. 1-13

1.5.1

 Digital Calibration............................................................................................................................... 1-13

1.5.2

 voltage/current Protection.................................................................................................................. 1-13

1.5.3

 Waveforms......................................................................................................................................... 1-13

1.5.4

 Saving and Recalling Settings ........................................................................................................... 1-14

1.5.5

 External Reference (Analog Control)................................................................................................. 1-14

1.5.6

 External Limits ................................................................................................................................... 1-14

1.5.7

 User-defined Voltage/Current Maximum Values (Software Limits) ................................................... 1-14

1.5.8

 Parallel and Series Configurations .................................................................................................... 1-14

1.5.9

 Energy Recuperation ......................................................................................................................... 1-14

1.6

 Equipment Supplied ................................................................................................................................ 1-15

1.7

 Accessories ............................................................................................................................................. 1-15

1.8

 Safety ...................................................................................................................................................... 1-15

SECTION 2 -  INSTALLATION

2.1

 Unpacking and Inspection ....................................................................................................................... 2-1

2.2

 Terminations and Controls ...................................................................................................................... 2-1

2.3

 Preliminary Operational Check................................................................................................................ 2-9

2.3.1

 Preliminary Operational Check using Analog Control........................................................................ 2-9

2.3.2

 Preliminary Operational Check using Digital Control......................................................................... 2-10

2.4

 Installation ............................................................................................................................................... 2-11

2.4.1

 Rack Mounting................................................................................................................................... 2-11

2.4.2

 Slide Installation................................................................................................................................. 2-11

2.5

 Wiring Instructions ................................................................................................................................... 2-12

2.5.1

 Safety Grounding............................................................................................................................... 2-12

2.5.2

 Source Power Connections ............................................................................................................... 2-12

2.5.3

 D-C Output Grounding....................................................................................................................... 2-12

2.5.3.1

 Grounding Network Configuration................................................................................................ 2-13

2.5.4

 Power Supply/Load Interface............................................................................................................. 2-13

2.5.5

 Load Connection - General................................................................................................................ 2-14

2.5.6

 Load Connection Using Local Sensing.............................................................................................. 2-14

2.5.7

 Load Connection Using Remote Sensing.......................................................................................... 2-14

2.6

 Cooling .................................................................................................................................................... 2-15

2.7

 Setting up the unit ................................................................................................................................... 2-15

2.7.1

 Power-up Settings ............................................................................................................................. 2-15

2.7.2

 Setup for Analog Control ................................................................................................................... 2-17

2.7.3

 Setup for Digital Control via GPIB ..................................................................................................... 2-17

2.7.4

 Setup for Digital Control via RS 232C ............................................................................................... 2-17

2.8

 Multiple Unit Configurations .................................................................................................................... 2-19

2.8.1

 Multiple Unit Connections .................................................................................................................. 2-19

2.8.2

 Multiple Unit Source Power ............................................................................................................... 2-24

2.8.3

 Multiple Unit Protection...................................................................................................................... 2-24

2.8.4

 Operating Instructions for Multiple Unit Combinations....................................................................... 2-25

2.8.5

 Restoring a Unit to Standalone Operation ......................................................................................... 2-26

Содержание BOP-GL 1KW















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BOP-GL 1KW

Wacker Neuson BPU 2540A Operator'S Manual preview
BPU 2540A
Бренд: Wacker Neuson Страницы: 40
BGS technic 62672 Quick Start Manual preview
62672
Бренд: BGS technic Страницы: 4
Sears 103.0305 Operating Instructions preview
103.0305
Бренд: Sears Страницы: 4
Parkside POFA 12 A2 Translation Of The Original Instructions preview
POFA 12 A2
Бренд: Parkside Страницы: 184
Ultra Products X-Finity Series Specification Sheet preview
X-Finity Series
Бренд: Ultra Products Страницы: 1
WAGO EPSITRON 787-602 Instruction Manual preview
EPSITRON 787-602
Бренд: WAGO Страницы: 2
SRC SRC-56P Instruction Manual preview
SRC-56P
Бренд: SRC Страницы: 6
Delta Electronika SM3300 Series Quick Start Manual preview
SM3300 Series
Бренд: Delta Electronika Страницы: 6
Natec TORPEDO UNI-70 User Manual preview
TORPEDO UNI-70
Бренд: Natec Страницы: 34
Caen ELS OCEM NGPS 100-100E User Manual preview
OCEM NGPS 100-100E
Бренд: Caen ELS Страницы: 102
NEO TOOLS 08-838 Original User Manual preview
08-838
Бренд: NEO TOOLS Страницы: 4
nextys NPSM40 Series Instruction Manual preview
NPSM40 Series
Бренд: nextys Страницы: 6
Cosel PAA100F Instruction Manual preview
PAA100F
Бренд: Cosel Страницы: 9
Sealey AUTO SERVICE VS2046 Instructions preview
AUTO SERVICE VS2046
Бренд: Sealey Страницы: 2
Far Tools 115339 Original Manual Translation preview
115339
Бренд: Far Tools Страницы: 23
Craftsman CMPBN18SB Instruction Manual preview
CMPBN18SB
Бренд: Craftsman Страницы: 36
CAMBRIONIX PD-Sync4 User Manual preview
PD-Sync4
Бренд: CAMBRIONIX Страницы: 16
Urrea SK904 User Manual And Warranty preview
SK904
Бренд: Urrea Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды