KEPCO BOP-GL 1KW Скачать руководство пользователя страница 163 | Manualshive

Страница: 163 / 174

background image

BOP-1KW-GL 111315

B-29

FIGURE B-10. USING PROT:LIM:POS AND PROT:LIM:POS COMMANDS TO SET ASYMMETRICAL LIMITS

B.97

[SOURce:]VOLTage[:LEVel]:PROTect[:BOTH]? QUERY

VOLT:PROT[:BOTH]?

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:PROT[:BOTH]?
Long Form: [SOURce:]VOLTage[:LEVel]:PROTect[:BOTH]?
Returns <exp_value>,<exp_value>

Description: Identifies the protection limits for voltage (positive, negative); maximum is 1% greater than rated out-

put voltage.

B.98

[SOURce:]VOLTage[:LEVel]:PROTect:MODE COMMAND

VOLT:PROT:MODE

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:PROT:MODE (EXT | FIX | LESS |)
Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:MODE (EXTernal | FIXed | LESSer |)
Description:Determines how voltage protection limits are controlled.
FIXED - Allows the limits to be controlled by digital commands.
EXTERNAL: Allows both current and voltage limits to be controlled by analog signals applied to the
analog port; limits set by SCPI command have no effect (see PAR. 3.4).
LESSER LIMIT: Allows protect limit to be automatically selected from either 1) the external analog
voltage applied to the Analog I/O port or 2) the value set from SCPI command. Whichever limit has a
lower absolute value (closest to zero) has effect.

B.99

[SOURce:]VOLTage[:LEVel]:PROTect:MODE? QUERY

VOLT:PROT:MODE?

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:PROT:MODE?
Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:MODE?
Returns FIX, EXT or LESS

Description: Identifies how voltage protection limits are controlled: FIX for Fixed, EXT for external, LESS for the

lesser of the internal (fixed) and external protection limit values (See PAR. B.98 for details).

B.100 [SOURce:]VOLTage[:LEVel]:PROTect:NEGative COMMAND

VOLT:PROT:NEG

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:PROT:NEG <exp_value>
Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:NEGative <exp_value>
where <value> is between minimum (box) value (Figure 1-3) and 1% above rated (nominal) output
voltage.

Description: Establishes the negative protection limit for voltage; maximum is 1% greater than rated output voltage.

B.101 [SOURce:]VOLTage[:LEVel]:PROTect:NEGative? QUERY

VOLT:PROT:NEG?

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:PROT:NEG?
Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:NEGative?
Returns: <exp_value>

Description: Identifies the negative protection limit for voltage.

NOTE:

The power supply is assumed to be operating in constant voltage mode.

VOLT:PROTECT:LIMIT:POS 5

Sets positive voltage protection limit to +5V.

VOLT:PROTECT:LIMIT:NEG 15

Sets negative voltage protection limit to -15V.

VOLT:PROTECT 10

Attempts to set voltage protection levels to ±10V. No error generated.

VOLT:PROT:POS?

Returns 5 (positive voltage protection set to +5V since 5 is less than
10.

VOLT:PROT:NEG?

Returns 10 (negative voltage protection set to -10V.

VOLT:PROTECT 18

Sets both voltage protection limits to +18V. No error generated.

VOLT:PROT:POS?

Returns 5 (positive voltage protection set to +5V since 5 is less than
18.

VOLT:PROT:NEG?

Returns 15 (negative voltage protection set to -15V, since 15 is less
than 18

«
...
161
162
163
164
165
...
»

Содержание BOP-GL 1KW















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BOP-GL 1KW

Бренд: Eastwood Страницы: 4

VisionXS-IP-C-DP-UHR

Бренд: G&D Страницы: 144

Бренд: SafetySpeed Страницы: 43

BAE PS-XA-3Y-24-250-609-I

Бренд: Balluff Страницы: 48

MAG-8200 Series

Бренд: Magna-Matic Страницы: 38

BOMAG BPR 50/55 D

Бренд: Fayat Страницы: 112

Бренд: Agilent Technologies Страницы: 47

Бренд: Palmgren Страницы: 46

Бренд: Universal Tool Страницы: 8

Бренд: Auplex Страницы: 3

S8VS - MODEL 15-30-60-90-120-180-240W

Бренд: Omron Страницы: 28

Бренд: Feider Machines Страницы: 18

Бренд: MaxPro Страницы: 112

Бренд: Kikusui Страницы: 170

Handy Master ABS9

Бренд: Fein Страницы: 108

Бренд: Mountz Страницы: 15

HEAVY DUTY M12 FTB

Бренд: Milwaukee Страницы: 77

Бренд: Hama Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды