KEPCO BOP-GL 1KW Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 174

background image

228-1352 SAFETY - (COVER REMOVAL) 111315

C

SAFETY INSTRUCTIONS

1. Installation, Operation and Service Precautions

This product is designed for use in accordance with EN 61010-1 and UL 3101 for Installation Category 2,
Pollution Degree 2. Hazardous voltages are present within this product during normal operation. The prod-
uct should never be operated with the cover removed unless equivalent protection of the operator from
accidental contact with hazardous internal voltages is provided:

2. Grounding

This product is a Class 1 device which utilizes protective earthing to ensure operator safety.

3. Electric Shock Hazards

This product outputs hazardous voltage and energy levels as a function of normal operation. Operators
must be trained in its use and exercise caution as well as common sense during use to prevent accidental
shock.

There are no operator serviceable parts or adjustments within the product enclosure.
Refer all servicing to trained service technician.

Source power must be removed from the product prior to performing any servicing.

This product is factory-wired for the nominal a-c mains voltage indicated on the rat-
ing nameplate located adjacent to the source power connection on the product's rear
panel. To reconfigure the product input for other nominal mains voltages as listed
herein, the product must be modified by a trained service technician.

The PROTECTIVE EARTHING CONDUCTOR TERMINAL must be properly con-
nected prior to application of source power to the product (see instructions on instal-
lation herein) in order to ensure safety from electric shock.

PROTECTIVE EARTHING CONDUCTOR TERMINAL - This symbol indicates the
point on the product to which the protective earthing conductor must be attached.

EARTH (GROUND) TERMINAL - This symbol is used to indicate a point which is
connected to the PROTECTIVE EARTHING TERMINAL. The component installer/
assembler must ensure that this point is connected to the PROTECTIVE EARTH-
ING TERMINAL.

CHASSIS TERMINAL -This symbol indicates frame (chassis) connection, which is
supplied as a point of convenience for performance purposes (see instructions on
grounding herein). This is not to be confused with the protective earthing point, and
may not be used in place of it.

This symbol appears adjacent to any external terminals at which hazardous voltage
levels as high as 500V d-c may exist in the course of normal or single fault condi-
tions.

This symbol appears adjacent to any external terminals at which hazardous voltage
levels in excess of 500V d-c may exist in the course of normal or single fault condi-
tions.

!

!

!

!

!

«
...
3
4
5
6
7
...
»

Содержание BOP-GL 1KW















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BOP-GL 1KW

Бренд: National Flooring Equipment Страницы: 49

Бренд: National Flooring Equipent Страницы: 33

Бренд: F.F. Group Страницы: 36

Бренд: Westfalia Страницы: 34

Бренд: Ferm Страницы: 96

Nuron TE 500-22

Бренд: Hilti Страницы: 188

Бренд: Wacker Neuson Страницы: 64

Бренд: Parker Страницы: 136

Бренд: Jet Страницы: 32

Бренд: Gallagher Страницы: 36

Бренд: Matco Tools Страницы: 13

Бренд: Dake Страницы: 15

Бренд: Parkside Страницы: 65

Бренд: Altrad Страницы: 128

Бренд: Universal Tool Страницы: 8

Бренд: Wacker Neuson Страницы: 74

Бренд: Milwaukee Страницы: 13

CE PAKMaster 75 XL Plus

Бренд: Thermal Dynamics Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды