KEPCO BOP-GL 1KW Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 174

background image

B

228-1529 COND/CONFORM 111315

Conditions of Conformance

When this product is used in applications governed by the requirements of the EEC, the following restric-
tions and conditions apply:

1.

For European applications, requiring compliance to the Low Voltage Directive, 73/23/EEC, this power
supply is considered a component product, designed for “built in“ applications. Because it is incom-
plete in construction, the end product enclosure must provide for compliance to any remaining electri-
cal safety requirements and act as a fire enclosure. (EN61010-1 Cl. 6, Cl. 7, Cl.8, Cl. 9 and EN61010-
1 annex F)

2.

This power supply is designed for stationary installation, with mains power applied via a detachable
power supply cord or via direct wiring to the source power terminal block.

3.

This power supply is considered a Class 1 (earthed) product, and as such depends upon proper con-
nection to protective earth for safety from electric shock. (EN61010-1 Cl. 6.5.4)

4.

This power supply is intended for use as part of equipment meant for test, measurement and labora-
tory use, and is designed to operate from single phase, three wire power systems. This equipment
must be installed within a suitably wired equipment rack, utilizing a three wire (grounded) mains con-
nection. See wiring section of this manual for complete electrical wiring instructions. (EN61010-1 Cl.
6.5.4 and Cl.6.10.1)

5.

This power supply has secondary output circuits that are considered hazardous, and which exceed
100V d-c, able to deliver current greater than 10A d-c.

6.

The output wiring terminals of this power supply have not been evaluated for field wiring and, there-
fore, must be properly configured by the end product manufacturer prior to use.

7.

This power supply employs a supplementary circuit protector in the form of a circuit breaker mounted
on the front panel. This circuit breaker protects the power supply itself from damage in the event of a
fault condition. For complete circuit protection of the end product, as well as the building wiring, it is
required that a primary circuit protection device be fitted to the branch circuit wiring. (EN61010-1 Cl.
9.6.2)

8.

Hazardous voltages are present within this power supply during normal operation. All operator adjust-
ments to the product are made via externally accessible switches, controls and signal lines as speci-
fied within the product operating instructions. There are no user or operator serviceable parts within
the product enclosure. Refer all servicing to qualified and trained Kepco service technicians.

«
...
2
3
4
5
6
...
»

Содержание BOP-GL 1KW















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BOP-GL 1KW

Бренд: Makita Страницы: 7

Бренд: Makita Страницы: 36

Бренд: Makita Страницы: 7

Бренд: Davey Water Products Страницы: 4

Бренд: Nation Flooring Equipment Страницы: 2

Бренд: Narex Страницы: 16

Бренд: NARGESA Страницы: 71

Бренд: U-Line Страницы: 15

Бренд: Marson Страницы: 6

Бренд: Senco Страницы: 32

Бренд: Sanela Страницы: 2

Бренд: Würth Страницы: 12

Бренд: Hama Страницы: 38

Бренд: Parkside Страницы: 258

2000-2 LNB Series

Бренд: Cross Technologies Страницы: 8

Бренд: Baileigh Industrial Страницы: 20

Бренд: Worcraft Страницы: 32

Бренд: KEPCO Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды