manualshive.com logo in svg

KEPCO BOP-GL 1KW, Руководство оператора

"KEPCO BOP-GL 1KW" - 1 кВт лабораторный источник питания с операторская инструкция для правильного использования. Бесплатное скачивание руководства для пользователя доступно на manualshive.com. Получите подробную информацию о продукте и его использовании, скачав руководство сейчас.

Поделиться
Скачать
background image

BOP-1KW-GL 111315

B-11

B.31

[SOURce:]CURRent[:LEVel]:PROTect:MODE COMMAND 

CURR:PROT:MODE

Syntax:

Short Form: [SOUR:]CURR[:LEV]:PROT:MODE (EXT | FIX | LESS |)
Long Form: [SOURce:]CURRent[:LEVel]:PROTect:MODE (EXTernal | FIXed | LESSer |)

Description: Determines how current protection limits are controlled.

FIXED - Allows the limits to be controlled by digital signals from SCPI commands.
EXTERNAL: Allows both current and voltage limits to be controlled by analog signals applied to the
analog port; limits set by SCPI command have no effect (see PAR. 3.4).
LESSER LIMIT: Allows protect limit to be automatically selected from either 1) the external analog limit
CURRent applied to the Analog I/O port or 2) the value set SCPI command). Whichever limit has a
lower absolute value (closest to zero) has effect. 

B.32

[SOURce:]CURRent[:LEVel]:PROTect:MODE? QUERY 

CURR:PROT:MODE?

Syntax:

Short Form: [SOUR:]CURR[:LEV]:PROT:MODE?
Long Form: [SOURce:]CURRent[:LEVel]:PROTect:MODE?
Returns FIXED, EXTERNAL or LESS

Description: Identifies how current protection limits are controlled. (See PAR. B.31 for details).

B.33

[SOURce:]CURRent[:LEVel]:PROTect:NEGative COMMAND 

CURR:PROT:NEG

Syntax:

Short Form: [SOUR:]CURR[:LEV]:PROT:NEG <value>
Long Form: [SOURce:]CURRent[:LEVel]:PROTect:NEGative <value>
where <value> is between minimum (box) value (Figure 1-3) and 1% above rated (nominal) output
current.

Description: Establishes the negative protection limit for current, maximum is 1% greater than rated (nominal) out-

put current. 

B.34

[SOURce:]CURRent[:LEVel]:PROTect:NEGative? QUERY 

CURR:PROT:NEG?

Syntax:

Short Form: [SOUR:]CURR[:LEV]:PROT:NEG?
Long Form: [SOURce:]CURRent[:LEVel]:PROTect:NEGative?
Returns <value>

Description: Identifies the negative protection limit for current.

B.35

[SOURce:]CURRent[:LEVel]:PROTect:POSitive COMMAND 

CURR:PROT:POS

Syntax:

Short Form: [SOUR:]CURR[:LEV]:PROT:POS <value>
Long Form: [SOURce:]CURRent[:LEVel]:PROTect:POSitive <value>
where <value> is between minimum (box) value (Figure 1-3) and 1% above rated (nominal) output
current.

Description: Establishes the positive protection limit for current, maximum is 1% greater than rated output current. 

B.36

[SOURce:]CURRent[:LEVel]:PROTect:POSitive?

 

QUERY 

CURR:PROT:POS?

Syntax:

Short Form: [SOUR:]CURR[:LEV]:PROT:POS?
Long Form: [SOURce:]CURRent[:LEVel]:PROTect:POSitive?
Returns <value>

Description: Identifies the positive protection limit for current.

B.37

[SOURce:]CURRent[:LEVel]:PROTect:LIMit[:BOTH] COMMAND

CURR:PROT:LIM[:BOTH]

Syntax:

Short Form: [SOUR:]CURR[:LEV]:PROT:LIM[:BOTH] <value>
Long Form: [SOURce:]CURRent[:LEVel]:PROTect:LIMit:[BOTH <value>
where <value> is between minimum (box) value (Figure 1-3) and 1% above rated (nominal) output
current.

Description: Establishes the maximum value possible for both the positive and negative protection limits for cur-

rent. Requires MEM:UPD (PAR. B.12) to save for power up. See PAR. 3.5.5.2 and Figure 3-6 for spe-
cial programming considerations.

Содержание BOP-GL 1KW















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BOP-GL 1KW

Array electronic 367 Series User Manual preview
367 Series
Бренд: Array electronic Страницы: 73
Cannondale AIR DUEL User Manual preview
AIR DUEL
Бренд: Cannondale Страницы: 12
Microtec SHT-20LP1 Manual preview
SHT-20LP1
Бренд: Microtec Страницы: 6
Parkside 315570 Translation Of The Original Instructions preview
315570
Бренд: Parkside Страницы: 49
Firepower Fatal1ty OCZ-FTY550W Instruction Manual preview
Fatal1ty OCZ-FTY550W
Бренд: Firepower Страницы: 20
Parkside 385161 2107 Original Instructions Manual preview
385161 2107
Бренд: Parkside Страницы: 38
M-system R8-PS1 Instruction Manual preview
R8-PS1
Бренд: M-system Страницы: 4
Tryton THG600 Operating Instruction preview
THG600
Бренд: Tryton Страницы: 48
Gardeo GKIT3.6VLIT-2IN1TRHLB Original Instructions Manual preview
GKIT3.6VLIT-2IN1TRHLB
Бренд: Gardeo Страницы: 29
Chef'sChoice DiamondHone 314 Instructions Manual preview
DiamondHone 314
Бренд: Chef'sChoice Страницы: 12
Stanley Fat Max FME340 Manual preview
Fat Max FME340
Бренд: Stanley Страницы: 84
Campbell Hausfeld SN268K00 Operating Instructions Manual preview
SN268K00
Бренд: Campbell Hausfeld Страницы: 12
nextys NUPS12 Instruction Manual preview
NUPS12
Бренд: nextys Страницы: 5
Baileigh MD-3500 Operator'S Manual preview
MD-3500
Бренд: Baileigh Страницы: 24
Yard force LX VSD1 Original Instructions Manual preview
LX VSD1
Бренд: Yard force Страницы: 13
Echo PB-250LN Operator'S Manual preview
PB-250LN
Бренд: Echo Страницы: 44
Universal Tool UT8963-17 Quick Start Manual preview
UT8963-17
Бренд: Universal Tool Страницы: 2
ENERMAX GALAXY EVO EGX850EWT Manual preview
GALAXY EVO EGX850EWT
Бренд: ENERMAX Страницы: 60

Бренды по названию

Популярные бренды

Загрузить еще бренды