KEPCO BOP-GL 1KW Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 174

background image

1-6

BOP-1K-GL 111315

PROGRAMMING CHARACTERISTICS (Continued)

Digital control

remote

IEEE 488-2 (GPIB) and RS 232

SCPI

remote

RS 485 (BITBUS)

IEEE 1118, used for series and parallel config-
urations

Status
Display

front panel Lights:

Unit Status: POWER / FAULT/LIMIT (lights green for Power OK, lights red for Fault,
lights orange for Limit).
Output Status: OUTPUT ON (lights green On, not lit for Off).
Mode of Operation: VOLTAGE/CURRENT (lights green for Voltage, lights yellow for
Current).
Control: DIGITAL CONTROL (lights green for Digital control, not lit for Analog con-
trol).
Type: MASTER/SLAVE (lights green for Standalone or Master, lights yellow for
Slave).

remote Output voltage and current read back on GPIB or RS 232 bus and on the analog

readback lines.

FUNCTION GENERATOR CHARACTERISTICS

(See PAR. 3.5.7)

Maximum number of waveforms

1

Lost when the unit is turned off, must be
saved on the host computer)

maximum number of points per basic wave-
form

3933

Maximum number of segments or basic wave-
forms per waveform

126

Or maximum number of points (whichever
comes first)

•

The time interval for each segment
depends on the type of waveform: period
for ramp and square waveforms, period or
fraction of period for sine and triangular
waveforms and time interval for DC levels

•

Waveforms that exceed the maximum
number of points are not executed and an
error message is generated.

Types of Basic waveforms

Sine (Sinusoidal waveform)

Triangle (Triangular waveform)

Pos. Ramp (Ramp waveform)

Neg. Ramp (Sawtooth waveform)

Square (50% Duty Cycle Pulse)

Level (DC waveform)

See LIST:CURR:APPLY (PAR. B.56) for cur-
rent waveforms, or LIST:VOLT:APPLY (PAR.
B.79) for voltage waveforms.

Count (Number of repetitions)

Range: 1 to 255

For Count = 0 the waveform is exe-

cuted indefinitely until stop com-

mand is sent

See LIST:COUNt command (PAR. ). When
the count is complete or the waveform is
stopped using the CURR:MODE FIX com-
mand (PAR. B.27) or VOLT:MODE FIX com-
mand (PAR. B.94) the output remains at last
output value. The BOP can also stop at the
end of a cycle by using the CURR:MODE
HALT or VOLT:MODE HALT command.

Waveform Parameters

Type: Voltage or Current

Count: number

Initial/Repeating

See LIST:CURR:APPLY (PAR. B.56) for cur-
rent waveforms, or LIST:VOLT:APPLY (PAR.
B.79) for voltage waveforms).

•

Type of waveform, voltage or current, can
be selected only for a new waveform and
consequently applies to all waveform seg-
ments.

•

All segments except the last may be set to
run once (using the LIST:COUN:SKIP com-
mand) or per the Count setting.

TABLE 1-2. BOP GENERAL SPECIFICATIONS (Continued)

SPECIFICATION

RATING/DESCRIPTION

CONDITION

«
...
24
25
26
27
28
...
»

Содержание BOP-GL 1KW















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BOP-GL 1KW

Бренд: F.F. Group Страницы: 44

Бренд: jbc Страницы: 12

Бренд: jbc Страницы: 8

Бренд: Artos Страницы: 185

Бренд: HELVAR Страницы: 2

Бренд: Robust Страницы: 44

Бренд: Wacker Neuson Страницы: 54

Бренд: H3C Страницы: 15

Бренд: MAIMAN ELECTRONICS Страницы: 24

Бренд: Radio Shack Страницы: 13

Бренд: Milwaukee Страницы: 36

Watt Series Programmable DC Power Supply XG...

Бренд: Xantrex Страницы: 286

Бренд: National Flooring Equipment Страницы: 44

Бренд: Shell Страницы: 20

BOSTITCH PROFESSIONAL QuietSharp Glow EPS11HC

Бренд: Stanley Страницы: 2

Бренд: Campbell Hausfeld Страницы: 12

Бренд: Xantrex Страницы: 31

Бренд: Kaindl Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды