manualshive.com logo in svg

KEPCO BOP-GL 1KW, Руководство оператора

"KEPCO BOP-GL 1KW" - 1 кВт лабораторный источник питания с операторская инструкция для правильного использования. Бесплатное скачивание руководства для пользователя доступно на manualshive.com. Получите подробную информацию о продукте и его использовании, скачав руководство сейчас.

Поделиться
Скачать
background image

BOP-1KW-GL 111315

B-27

B.87

[SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude]? QUERY 

 

VOLT?

Syntax:

Short Form: [SOUR:]VOLT[:LEV][:IMM][:AMP]? {MIN | MAX}
Long Form: [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude]? {MIN | MAX}

Description:

Identifies programmed voltage, maximum allowable voltage, or minimum voltage. 

The VOLT?

query returns the programmed value of voltage. Actual output voltage will depend on load conditions.
The VOLT?MAX query returns the maximum voltage allowed for a particular model. VOLT? MIN
returns minimum voltage allowed for power supply (always negative). 

Related Commands:

 VOLT.

(See example, Figure B-1.)

B.88

[SOURce:]VOLTage[:LEVel]:LIMit[:BOTH] COMMAND 

VOLT:LIM[:BOTH]

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:LIM[:BOTH] <value>
Long Form: [SOURce:]VOLTage[:LEVel]:LIMit[:BOTH] <value>
where <value> is between zero and rated (nominal) output voltage

Description: Establishes the software limit <value> for output voltage, i.e., sets the maximum value of positive or

negative output voltage that the unit will be allowed to produce. Requires MEM:UPD (PAR. B.12) to
save for power up. See PAR. 3.5.5.2 and Figure 3-6 for special programming considerations.

B.89

[SOURce:]VOLTage[:LEVel]:LIMit[:BOTH]? QUERY 

VOLT:LIM[:BOTH]?

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:LIM[:BOTH]?
Long Form: [SOURce:]VOLTage[:LEVel]:LIMit:[:BOTH]?
Returns <value> 

Description: Identifies the software limit value for both positive and negative output voltage specified by the user.

B.90

[SOURce:]VOLTage[:LEVel]:LIMit:NEGative COMMAND 

VOLT:LIM:NEG

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:LIM:NEG <value>
Long Form: [SOURce:]VOLTage[:LEVel]:LIMit:NEGative <value>
where <value> is between zero and rated (nominal) output voltage

Description: Establishes the software limit <value> for negative output voltage, i.e., sets the maximum value of

negative output voltage that the unit will be allowed to produce. Requires MEM:UPD (PAR. B.12) to
save for power up. See PAR. 3.5.5.2 and Figure 3-6 for special programming considerations.

B.91

[SOURce:]VOLTage[:LEVel]:LIMit:NEGative? QUERY 

VOLT:LIM:NEG?

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:LIM:NEG? <value>
Long Form: [SOURce:]VOLTage[:LEVel]:LIMit:NEGative? <value>

Description: Identifies the software limit value for negative output voltage specified by the user.

B.92

[SOURce:]VOLTage[:LEVel]:LIMit:POSitive COMMAND 

VOLT:LIM:POS

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:LIM:POS <value>
Long Form: [SOURce:]VOLTage[:LEVel]:LIMit:POSitive <value>
where <value> is between zero and rated (nominal) output voltage

Description: Establishes the software limit <value> for positive output voltage, i.e., sets the maximum value of pos-

itive output voltage that the unit will be allowed to produce. Requires MEM:UPD (PAR. B.12) to save
for power up. See PAR. 3.5.5.2 and Figure 3-6 for special programming considerations.

B.93

[SOURce:]VOLTage[:LEVel]:LIMit:POSitive? QUERY 

VOLT:LIM:POS?

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:LIM:POS? <value>
Long Form: [SOURce:]VOLTage[:LEVel]:LIMit:POSitive? <value>

Description: Identifies the software limit value for positive output voltage specified by the user.

Содержание BOP-GL 1KW















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BOP-GL 1KW

Pulsar PSD12020 Manual preview
PSD12020
Бренд: Pulsar Страницы: 2
Mannesmann Demag 60028916 Operating Manual preview
60028916
Бренд: Mannesmann Demag Страницы: 17
Omer 80.16 ROC2 Instructions Manual preview
80.16 ROC2
Бренд: Omer Страницы: 26
Kett KL-200 Instructions For Use Manual preview
KL-200
Бренд: Kett Страницы: 6
Delta Electronics DRP024V060W1BA Manual preview
DRP024V060W1BA
Бренд: Delta Electronics Страницы: 13
Roebuck RB3130 Operator'S Manual preview
RB3130
Бренд: Roebuck Страницы: 16
Far Tools one LI 144 Original Manual Translation preview
one LI 144
Бренд: Far Tools Страницы: 30
Hilti SIW 22T-A 1/2 inch Original Operating Instructions preview
SIW 22T-A 1/2 inch
Бренд: Hilti Страницы: 46
MADER 63102 Instructions Manual preview
63102
Бренд: MADER Страницы: 44
Hama 00223619 Operating Instructions Manual preview
00223619
Бренд: Hama Страницы: 40
Oltronix Racpac 300 Operating And Service Manual preview
Racpac 300
Бренд: Oltronix Страницы: 94
Cembre BTEPE2.DET10 Operation And Maintenance Manual preview
BTEPE2.DET10
Бренд: Cembre Страницы: 12
G-Tec Basic TTCF-6 How To Operate preview
Basic TTCF-6
Бренд: G-Tec Страницы: 11
YOKOGAWA DOX10 User Manual preview
DOX10
Бренд: YOKOGAWA Страницы: 21
Parkside PFBS 12 B4 Translation Of The Original Instructions preview
PFBS 12 B4
Бренд: Parkside Страницы: 50
Denzel 26121 User Manual preview
26121
Бренд: Denzel Страницы: 29
Altrad ATIKA 302360 Original Instructions Manual preview
ATIKA 302360
Бренд: Altrad Страницы: 128
KEPCO TBC Series Instruction Manual preview
TBC Series
Бренд: KEPCO Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды