KaVo ProXam iOS Скачать руководство пользователя страница 15

Страница: 15 / 130

WARNING

Portable RF communications equipment (including peripherals such as

antenna cables and external antennas) should be used no closer than 30

cm (12 inches) to any part of the scanner, including cables specified by the

manufacturer. Otherwise, degradation of the performance of this equipment

could result. The wireless components in the scanner may be interfered

with by other equipment, even if the other equipment is fully compliant with

CISPR emission requirements.

CAUTION

After using the scanner on a patient, clean the scanner according to the

cleaning instructions found in section "Cleaning / preventive maintenance"

on page 101.

CAUTION

Do not hold the scanner in a way that will cover the cooling vents.

CAUTION

Do not immerse the scanner base in liquid or expose the scanner to

conditions outside the operating conditions, see section "KaVo ProXam iOS

specification" on page 108. Clean the scanner according to the instructions

in section "Cleaning / preventive maintenance" on page 101.

CAUTION

Do not stack the tips near or on any other metal instruments.

CAUTION

Ensure your scanner is properly maintained, see section "Cleaning /

preventive maintenance" on page 101.

CAUTION

If you suspect equipment malfunction or failure, discontinue using the

scanner and contact technical support immediately. Do not attempt to make

any repairs on the scanner.

CAUTION

Read and comply with all safety, warning, and instructional labels on the

scanner.

CAUTION

If the scanner has been operational for an extended period of time, the

surface may become warm to the touch. If the temperature becomes too

warm to the touch within a minute of use, turn it off and allow it to cool. The

surface of the applied part (scanning tip) may reach a temperature of 43°C

during normal operation. This is necessary to prevent fogging of the mirror

and is safe for patient contact.

4.1 Reporting serious incidents

Serious incidents that have occurred in relation to the device must be

reported to the manufacturer and the local competent authority.

4 Safety precautions

Instructions for use

KaVo ProXam iOS 9

Содержание ProXam iOS



































































































































Результаты поиска

Содержание ProXam iOS

Отзывы:

Бренды по названию

Популярные бренды

KaVo ProXam iOS, Инструкция по эксплуатации

Результаты поиска

Содержание ProXam iOS

Отзывы:

Бренды по названию

Популярные бренды