Juniper JUNOSE 11.1.X MULTICAST ROUTING Скачать руководство пользователя страница 172 | Manualshive

Страница: 172 / 270

background image

References

For more information about IPv6 multicast, see the following resource:

■

A “ traceroute” Facility for IP Multicast—draft-ietf-idmr-traceroute-ipm-07.txt
(January 2001 expiration)

Before You Begin

You can configure multicast on IPv4 and IPv6 interfaces.

For information about configuring IP interfaces, see

Configuring IP

in the

JUNOSe IP,

IPv6, and IGP Configuration Guide

. For information about configuring IPv6 interfaces,

see

Configuring IPv6

in

JUNOSe IP, IPv6, and IGP Configuration Guide

.

For information about configuring multicast on IPv4 interfaces, see “Configuring
IPv4 Multicast” on page 3.

Configuring the Switching Fabric Bandwidth

By default, the switch fabric for the ERX1440, ERX310, E120, and E320 Broadband
Services Routers uses a bandwidth weighting ratio of 15:2 for multicast-to-unicast
weighted round robin (WRR). In the absence of strict-priority traffic, and when both
unicast and multicast traffic compete for switch fabric bandwidth, the switch fabric
allocates 15/17ths of the available bandwidth to multicast traffic and 2/17ths of the
available bandwidth to unicast traffic.

You can use the

fabric weights

command to change the ratio for multicast to unicast

traffic on the router switch fabric. For more information about the

fabric weights

command, see

Managing the System

in the

JUNOSe System Basics Configuration Guide

.

Enabling IPv6 Multicast

In this implementation, IPv6 multicast works on VRs. By default, IPv6 multicast is
disabled on a VR. To enable IPv6 multicast on a VR, access the context for a VR, and
then issue the

ipv6 multicast-routing

command.

ipv6 multicast-routing

■

Use to enable IPv6 multicast routing on the VR.

■

By default, IPv6 multicast is disabled on the VR. In the disabled state, all multicast
protocols are disabled, and the VR forwards no multicast packets.

■

Example

host1(config)#

ipv6 multicast-routing

■

Use the

no

version to disable IPv6 multicast routing on the VR (the default).

■

See ipv6 multicast-routing.

150

■

References

JUNOSe 11.1.x Multicast Routing Configuration Guide

«
...
170
171
172
173
174
...
»

Содержание JUNOSE 11.1.X MULTICAST ROUTING















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.1.X MULTICAST ROUTING

4116 - SCX B/W Laser

Бренд: Samsung Страницы: 14

2252W - Printer - B/W

Бренд: Samsung Страницы: 10

System Storage DS3000

Бренд: IBM Страницы: 38

Бренд: Savin Страницы: 71

App for Android

Бренд: TomTom Страницы: 58

Бренд: MACROMEDIA Страницы: 624

ANTI-VIRUS 2011 - REV 2011.11

Бренд: AVG Страницы: 209

Бренд: Vonamic Страницы: 31

Бренд: Navman Страницы: 52

Бренд: DivX Страницы: 59

AVC HD Player 5.7

Бренд: Elecard Страницы: 39

Бренд: Z3 Technology Страницы: 8

Бренд: GAI-Tronics Страницы: 5

Gatekeeper/Border Controller API D14172.01

Бренд: TANDBERG Страницы: 84

Бренд: Canon Страницы: 101

IDENTITY MANAGER 3.6.1

Бренд: Novell Страницы: 54

Бренд: JVC Страницы: 32

Бренд: JVC Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды